Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Tascam Dateigröße: 98.54 kb Dateiname: 1400704_PM_EN.pdf Unterrichtssprache:

Take up any slack in the tape by turning the cassette’s hub with a pencil or your finger. If you do not remove excess slack, the tape might become tangled in the record/playback mechanism. Avoid touching the tape. 2. Press STOP/EJECT to open the cassette compartment door. 3 3. Load the cassette with its open edge facing up, its full reel to the right, and the side you want to play facing out. 4. Gently close the compartment door. PLAYING A CASSETTE TAPE 1. Set FUNCTION to TAPE. 2. Load a cassette tape. 3. Press PLAY. 4. Adjust VOLUME as desired. 5. Press STOP/EJECT to stop playback before it automatically stops at the end of the tape. Press STOP/EJECT again to open the cassette compartment so you can remove the cassette tape. RECORDING You can record from the radio, or use the built-in microphone to make a live recording. Caution: Before you load a cassette tape for recording, be sure its erase-protection tabs are in place. If you force down RECORD when that side’s erase-protection tab is missing, you can damage the record mechanism (see “Preventing Accidental Erasure” on Page 5). Note: Tape quality greatly affects the quality of the recording. We recommend extended- range or low noise type 1 regular length (60or 90-minute) normal-bias cassette tapes. We do not recommend long-play cassette tapes such as C-120s because they are extremely thin and can easily tangle in the playback mechanism. Recording from the Radio 1. Load a blank cassette tape or one you want or record over into the cassette compartment. 2. Set FUNCTION to RADIO. 3. Set BAND to the desired setting. 4. Adjust TUNING to the station you want to record. 5. Press RECORD to begin recording. Both PLAY and RECORD lock down. 6. Press STOP/EJECT to stop recording. Both RECORD and PLAY release. Making Live Recordings Follow these steps to make a live recording using the built-in microphone. 1. Load a blank cassette tape or one you want to record over into the cassette compartment. 2. Set FUNCTION to TAPE. 3. Place the cassette recorder 2–3 feet from the recording source. 4. Press RECORD to begin recording. Both PLAY and RECORD lock down. 5. Press STOP/EJECT to stop recording. Both RECORD and PLAY release. TAPE TIPS Restoring Tape Tension and Sound Quality After you play a cassette tape several times, the tape might become tightly wound on the reels. This can cause playback sound quality to deteriorate. To restore the sound quality, fast-forward the tape from the beginning to the end of one side, then completely rewind it. Then loosen the tape reels by gently tapping each edge of the cassette on a flat surface. Caution: Be careful not to damage the cassette when tapping it. Do not touch the exposed tape or allow any sharp objects near the cassette. 4 Erasing Tapes To record over a cassette tape, simply record as usual. The cassette deck records over the previous recording. You can quickly erase both sides of a cassette tape using a RadioShack bulk tape eraser. Note: If you use metal or high-bias type tape, the recorded sound might not be erased properly. Preventing Accidental Erasure Cassette tapes have two erase-protection tabs — one for each side. When a tab is in place, you can record on that side. To prevent accidental erasure of a tape recording, use a screwdriver to remove one or both of the cassette tape’s erase-protection tabs. This prevents RECORD from being pressed. If you later decide to record on a tape side after you have removed the erase-protection tab, place a piece of strong plastic tape over that side’s erase-protection hole. Be sure you cover only the hole originally covered by the erase-protection tab. Caution: Removing the erase-protection tabs does not prevent a bulk eraser from erasing a cassette tape. Cleaning the Tape-Handling Parts Dirt, dust, or particles of the tape’s coating can accumulate on the tape heads and other parts that the tape touches. This can greatly reduce the performance of the cassette player. After every 20 hours of tape player operation, follow these steps to clean the tape-handling parts or use a RadioShack cassette deck cleaning kit. 1. Remove the batteries and disconnect any other power source. 2. Set FUNCTION to TAPE. 3. Open the cassette compartment door and press PLAY to expose the tape-handling parts. 4. Hold down the erase-protection tab sensor, then press RECORD to expose the record/playback and erase heads. Erase-Protection Tab Sensor 5. Use a cotton swab dipped in tape head cleaning solution or denatured alcohol to gently clean the capstans, pinch roller, tape guides, and tape heads. Capstan Record/Playback Tape Guides Head Erase Head Pinch Roller 6. Press STOP/EJECT and close the cassette compartment door, then reinstall the batteries or reconnect the power source. 5 Modifying or tampering with the cassette re- CARE corder’s internal components can cause a Keep the cassette recorder dry; if it gets wet, malfunction and might invalidate its warranty wipe it dry immediately. Use and store the and ...

Herunterladen

Geben Sie zwei Ziffern: