Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
2 Cassette recorder keys: PAUSE ; – pauses playback or recording STOP•EJECT 9/ – stops playback or recording. – opens the cassette holder. F. FWD/REWIND 5 or 6 – fast winds/rewinds the tape PLAY 1 – starts playback RECORD 0 – starts recording 3 VOLUME rotary – adjusts volume level 4 p - 3.5mm stereo headphone jack Helpful hints: – Connecting the headphones will switch off the speakers. 5 MIC (built-in microphone) – for voice recording 6 Band selector: MW, FM – selects wavebands, MW or FM 7 Source selector:TAPE, RADIO – selects tape or radio source of sound – switches off the set 8 TUNING rotary – tunes to radio stations Back panel (See 1) 9 Telescopic antenna - improves FM reception. 0 AC INPUT - inlet for power cord ! Voltage selector – (inside the battery compartment, not for all versions) adjust to match the local voltage 110/220V before plugging in the set. @ Battery door - open to insert 6 X 1.5 batteries, type R20 or D-cells Power supply Whenever convenient, use the power cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries. Batteries (not included) • Insert 6 batteries, type R20 or D-cells (preferably alkaline) with the correct polarity. (See 1) Batteries contain chemical substances, so they should be disposed of properly. • Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst: • Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not try to mix old batteries with the new ones. • Remove the batteries if the set is not to be used for a long time. Power Supply General Operation/ Radio Using AC power 1 Check if the power voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 2 If your set is equipped with a voltage selector, adjust the selector so that it matches with the local mains. 3 Connect the power cord to the AC INPUT inlet and the wall socket.The power cord is now connected and ready for use. 4 To switch the set off completely, withdraw the power cord from the wall socket. • Disconnect the power cord from the wall socket to protect your set during heavy thunderstorms. Helpful hints : To avoid unnecessary energy consumption, always adjust the Source selector to TAPE after using the set. Also check that the tape deck keys are released. The type plate is located on the bottom of the set. CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. General operation Switching on and off and selecting functions 1 To switch on, push the Source selector slider to TAPE or RADIO as desired. 2 To switch off, push the Source selector to TAPE and check the cassette keys are released. Helpful hints: – To change from TAPE to RADIO , or when you are switching off the set: first, make sure you press the STOP•EJECT 9/ key to end playback and all the cassette keys are released. Adjusting volume • Adjust the volume with the VOLUME control. Radio reception 1 Adjust the source selector to RADIO. 2 Adjust the band selector to select your desired waveband, MW or FM. 3 Turn TUNING to tune to a station. -FM STEREO lights up for stereo FM reception. 4 To switch off the radio, adjust the source selector to TAPE position. To improve radio reception: • For FM, extend and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. • For MW, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. Cassette Recorder Cassette playback 1 Push the Source selector to TAPE 2 Press STOP•EJECT 9/ to open the cassette holder and insert a cassette and close the deck. 3 Press PLAY 1 to start playback. 4 To pause playback press PAUSE ;. To resume, press the key again. 5 By pressing F.FWD/REWIND 5 or 6, fast forwading/ rewinding of the tape is possible in both directions.To stop fast winding, press 9//. 6 To stop the tape, press 9//. Helpful hints: – During playback, the keys are automatically released at the end of a tape and the set is switched off (unless PAUSE ; mode has been activated.) – During fast forwarding/rewinding, the keys will not be released at the end of a tape.To switch off the set, make sure the cassette keys are also released. The making of unauthorized copies of copy-protected material, including com- puter programmes, files, broadcasts and sound recordings, may be an infringe- ment of copyrights and constitute a criminal offence.This equipment should not be used for such purposes. General information on recording • Recording is permissible insofar as copyright or. other rights of third parties are not infringed. • For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been brok...