Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
The 3.5 mm also be connected to the minus pole - . • Connect the mains adapter • Always disconnect the mains Battery (optional) • Open battery door and insert two alkaline UM3 or AA as indicated. Use of Philips POWERLIFE batteries gives up to 18 hours of cassette playback. • Remove the batteries from the set if they are exhausted not to be used for a long time. ™ When the batteries are running low, will flash briefly in the display and you should insert new batteries. If the radio is on, it will automatically switch off. ™ It may be necessary to reprogramme your preset stations. MEMORY PROTECTION The memory protection power failure or interruption. When changing batteries presets and the last station approximately 2 minutes. This or power supply without having to again. GENERAL SETTING Reset button Should you receive from carpets, thunderstorms, electronic functions of your clear all data (e.g. tuning step, start up again. • Use a ball point pen to press the RESET button, found on the back of the cassette door. Locking This button helps you to prevent any of the other controls from being accidentally pressed when you listening to the radio or when you are not using the 1 Press the LOCK button ™ appears in the display when LOCK is activated. 2 To deactivate the LOCK function, press LOCK again. ™ disappears from the display. CLOCK DISPLAY The time is displayed system. The seconds ‘ : ’ second by second, and clock display, where each segment represents 5 seconds. 1 In the time mode, press ENTER. ™ The clock digits will flash for 5 seconds. 2 To set the hour/ minutes for the clock time, HR or MIN while the display is still flashing. ™ With your finger held down on HR , the hour will increase steadily as a number from 1-12 or 0-23. Release HR when you reach the approximate time setting. ™ With your finger held down on MIN, the minutes will increase rapidly and continuously. Press briefly and repeatedly if you need to adjust the minutes slowly. 3 Press the ENTER button a second time to confirm the time setting. ™ The clock digits will stop flashing. English SETTING RADIO English CHANGING THE In North and South adjacent channels in AM (MW) band is 10 KHz. In the rest of the world this step 9 KHz. Usually the frequency step has been preset in the factory The tuning step on this set is also display where: 10 KHz uses the 12-hr clock 9 KHz uses the 24-hr clock All preset stations will be lost and need to be programmed again when you change the tuning step. 1 In the radio mode, press and hold ENTER. ™ The radio station frequency will disappear from the display. 2 Without releasing ENTER, press and also hold down: • TUNING + (up) 5 seconds or more to select a tuning step of 10 KHz and the 12-hr clock. ™ The display shows ‘ U’ briefly. • TUNING – (down) 5 seconds or more to select a tuning step of 9 KHz and the 24-hr clock. ™ The display shows ‘ E’ briefly. 1 Connect the headphones psocket. 2 To switch on the radio • press RADIO ON-OFF once for AM (MW) • press RADIO ON-OFF twice to select FM ™ STEREO appears on the display when FM stereo transmission. 3 Select your station by one of the following: ™ by using the – TUNING + control (down or up); ™ pressing one of the Preset memory buttons 0-9 for a preset station; ™ Direct Access Tuning, by entering the known band frequency. 4 Adjust the sound with VOLUME and DBB (Dynamic Bass Boost) controls. 5 To turn off the radio, press RADIO ON-OFF once or until the display shows OFF and reverts to the clock mode. To improve reception: FM: The headphone cord functions as the FM-aerial. Extend it fully and position the cord. AM: Uses the built-in aerial. Turn the set to find the best position. RADIO TUNING Direct Access tuning The frequency of the known. You can find these radio guides. 1 In the radio mode, press ENTER. ™ The current frequency in the display 2 Use the Preset memory buttons to enter desired frequency within a 5 second period. 3 Press ENTER again to confirm your radio station. ™ The display shows the selected frequency or the nearest frequency. ™ If you have made an incorrect entry, Err will appear in the display. Entry examples of bands and frequencies: e.g.i 98.1 MHz, FM: Press 9,8,1 and ENTER e.g.ii 603 KHz, AM (MW): Press 6,0,3 and ENTER Manual tuning • Press TUNING – or + briefly, once or as until the right frequency can be changed step by Automatic tuning 1 Press and hold down the TUNING – or + control until the display frequency starts to run. 2 When a station of sufficient strength has will stop, or you can stop the automatic tuning the TUNING – or + control again. 3 Repeat until you have found the desired station. SELECTING & STORING FREQUENCIES: PRESETS You can store the frequencies of 20 radio stations in the memory, 10 on each waveband. A stored frequency is only erased from the memory by storing another frequency in its place, or if you reset your unit. 1 Select the waveband and tune to your desired station. 2 Select and press one of the Preset memory butt...