Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Radio Shack Dateigröße: 388.62 kb Dateiname: 1401117_PM_EN_reva.pdf Unterrichtssprache:

Both are available at your local RadioShack store. Caution: You must use a Class 2 power source that supplies 6V DC and delivers 300mA. Its center tip must be set to negative and its plug must fit the recorder's DC 6V jack. Using an adapter that does not meet these specifications could damage the recorder or the adapter. 1. Set the adapter’s voltage switch to 6V. 2. Attach the Adaptaplug to the adapter’s cord with the tip set to negative. 3. Insert the adapter’s barrel plug into the recorder’s DC 6V jack. This disconnects the batteries. 4. Plug the other end of the adapter into a standard AC outlet or a DC power source. ! Step One EAR — Connect the supplied earphone here for private listening. Cassette tape compartment DC 6V — Connect an adapter and use AC or DC power. MIC — Connect an external AUX — Connect an external audio source so that you can record from it. REM — Connect an external microphone here if the Step Four Step Three microphone has remote Loading a Cassette Playing a Cassette control capability. 1. Remove any slack from the cassette tape 1. Load a cassette tape in the compartment. by turning one of the hubs with a pencil. The tape might become tangled in the 2. Rotate VOLUME to MIN for low sound. MIN-VOLUME-MAX — Adjust record/playback mechanism if you do not playback volume to the desired microphone, if desired. remove excess slack. listening level. Step Two Connecting Earphones Use the supplied earphone for private listening. Insert the earphone’s plug into the recorder’s EAR jack. Connecting the earphone automatically disconnects the built-in speaker. Listening Safely • Set the volume to the lowest setting before you begin listening. After you begin listening, adjust the volume to a comfortable level. • Do not listen at extremely high volume levels. Extended high-volume listening can lead to permanent hearing loss. • Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a volume level that does not cause discomfort might still damage your hearing. Traffic Safety • Do not wear earphones while operating a motor vehicle or riding a bicycle. This can create a traffic hazard and could be illegal in some areas. • Even though some earphones let you hear some outside sounds when listening at normal volume levels, they still can present a traffic hazard. O BATTERY NOTES O • Dispose of old batteries promptly and properly. • Do not burn or bury batteries. • Use fresh batteries of the required size and recommended type. • Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. • If you do not plan to use the recorder for a month or more, remove the batteries. Batteries can leak chemicals that can damage electronic parts. 3. Press PLAY. The tape begins to play. 2. Press STOP/EJECT to open the cassette compartment door. 4. Adjust VOLUME to the desired listening level. 3. Insert the tape with its open edge outward 5. To stop playback before the tape reaches the end, press toward the controls, and the desired side STOP/EJECT. Otherwise, the tape will automatically stop playing facing up. once it reaches the end. 4. Close the door. 6. Press STOP/EJECT again to open the cassette compartment door and remove the cassette. Step Five Recording 1. Load a cassette tape in the compartment. Using the Built-In Microphone 2. Connect an external microphone. 1. Load a cassette tape in the compartment. If the external microphone has a 1/8-inch plug, insert it into the recorder’s MIC jack. 2. Place the recorder as close as possible to the recording source (within 2-3 feet, if possible). If the external microphone has two plugs and an On/Off switch, this means you can remotely control the recorder 3. Press RECORD. Both PLAY and RECORD automatically from your microphone. Insert the microphone’s 1/8-inch remain pressed down, and the RECORD/BATT LED lights plug into the recorder’s MIC jack, and the smaller plug into while recording. the REM jack. 4. Press PAUSE at any time to temporarily stop recording. To 3. Press RECORD. Both PLAY and RECORD automatically resume recording, press PAUSE again. remain pressed down. 5. Press STOP/EJECT to stop recording. 4. If you are using an external microphone with an On/Off switch, set the switch to ON. Using an External Microphone You can connect an external 1/8-inch plug to the recorder. 5. Speak into the microphone. Depending on the type of microphone you use, this is handy when you want to record only an individual’s voice or exclude 6. Press STOP/EJECT to stop recording. other sounds in the surrounding area. Your local Radioshack store carries a wide variety of microphones. Limited 90-Day Warranty Specifications Recommended Tapes Tape quality greatly affects the quality of the recording. We recommend extended-range or low noise Type 1 regular length (60 or 90 minute) normal-bias cassette tapes. We do not recommend long-play cassette tapes such as ...

Herunterladen

Geben Sie zwei Ziffern: