3 Can be programmed only on the Auxiliary key and the optional speaker/ microphone PF (orange) key. Available only for P2 operation. Can be programmed only on the microphone programmable function keys. Available only if the Secure Cryptographic Module (SCM) optional board has been installed. 8 BASIC OPERATIONS Switching power on/oFF Turn the Power switch/ Volume control clockwise to switch the transceiver ON. Turn the Power switch/ Volume control counterclockwise fully to switch the transceiver

No. Name Description Impedance I/O 1SSWExt/IntSpeakerSwitchInputHighImpedanceI2SP+BTLOutput+forExternalSpeaker8 ./ 16 . O3SP-BTLOutput-forExternalSpeakerO4MSWExt/IntMICSwitchInputHighImpedanceI5EMCExternalMICInput1.8 k. I6 MEExternalMICGNDGND- 7PTTExternalPTTInputHighImpedanceI8PFProgramableFunctionKeyInputHighImpedanceI9OPTManDownInputHighImpedanceI10EGNDGND- 115V5Vpowersupplyoutput5VO12TXDSerialDataOutputCMOSO13RXDSerialDataInputCMOSI14NCNotused-- Antenna Terminal 50 . impedance Battery Termin

. The ambient temperature should be between 41°F and 104°F (5°C and 40°C) while charging is in progress. Charging outside this range may not fully charge the battery. . The battery pack life is over when its operating time decreases even though it is fully and correctly charged. Replace the battery pack. 8 INSTALLING/ REMOVING THE BATTERY PACK . Do not short the battery terminals or dispose of the battery by fire. . Never attempt to remove the casing from the battery pack. 1 Align the battery pa

• The VOX Gain can be adjusted from levels 1 to 10 and OFF. • The transceiver announces the VOX Gain level as you adjust it. If OFF is selected, a beep sounds. 5 Press the PTT switch to save the setting. • A beep will sound. • The transceiver announces the new VOX Gain level. 6 Turn the transceiver power OFF and the ON again to activate VOX. Note: . If a speaker/ microphone is connected to the transceiver while the VOX function is switched ON and the VOX Gain level is configured to a higher, mor

• If an abnormal odor or smoke is detected coming from the transceiver, immediately switch OFF the power and remove the batteries from the transceiver. Contact your KENWOOD dealer. . Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. . Illegal operation is punishable by fine and/or imprisonment. SAFETY: It is important that the operator is aware of and understands hazards common to the operation of any transceiver. CONTENTS UN

We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS COVERED BY THIS MANUAL TK-2202L: 16-channel VHF FM Transceiver TK-3202L: 16-channel UHF FM Transceiver NOTICES TO THE USER . Government law prohibits the operation of unlicensed radio transmitters

Release the key to return to normal operation. 12 SCAN Scan is useful for monitoring signals on the transceiver channels. When scanning, the transceiver checks for a signal on each channel and only stops if a signal is present. The transceiver will remain on a busy channel until the signal is no longer present. Your dealer programs the delay time between signal drop-out and Scan resumption. If a signal is received during the delay time, the transceiver will remain on the same channel. Note: You

(For example 146.100 MHz) 3. Press the F key momentarily. The F indicator will turn on and the memory channel indicator will turn on. 4. Press the CALL key within 10 seconds of pressing the F key to enter the data into memory. A long beep will sound and the F indicator and memory channel indicators will turn off to confirm data entry. 4-4-5. Memory Channel Recall When recalling a memory channel using this procedure you will not be able to adjust the frequency or tone data. This form of memor

the transmit/receive frequencies are exactly the reverse of another repeater. For example repeater A uses 146.000 for a transmit frequency (OUTPUT) and 146.600 for receive (INPUT). Repeater B uses 146.000 for its receive and 146.600 for its transmit frequency. It would be inconvenient to have to reprogram the transceiver each time if you were in range of both repeaters. The REV key allows you to reverse the transmit and receive frequencies. To use the REVERSE function press the REV key. The off

Paging Code Memories There are 1 1 paging code memories. Use A Store your station ID code in memory. 0 Automatically stores the calling station's code during reception. Can temporarily set the code for the station to be called. 1-9 Stores group codes and local station codes in memory. 4-9-2. Setting the Paging Codes 1. Press the F key, then press the DTSS/PAG key. The P indicator will light. (PAGING MODE) 2. Press the ENT key to enter the CODE SETTING MODE. 3. Select memories (A, 0 to