Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Teleflex Marine Dateigröße: 445.83 kb Dateiname: Unterrichtssprache:

Measure and cut two lengths of Black 16 engine. AWG marine quality wire of sufficient 8. Remove Lanyard. Engine should stop length to connect one Interrupt Switch immediately. terminal to the Emergency Stop Wire and the other terminal to a System Ground. See Diagram B. IF ENGINE FAILS TO STOP, RECHECK 5. Strip one end of each wire and crimp on ALL WIRING. SHOULD THE ENGINE an insulated 1/4 inch female disconnect FAIL TO START OR STOP, OR RESUMES terminal. A crimping tool designed for RUNNING WITH THE LANYARD FORK insulated terminals MUST be used. REMOVED, CONSULT YOUR LOCAL 6. Attach the female disconnects to each of MARINE DEALER FOR ASSISTANCE. the male terminals on the Interrupt Switch. 7. Attach the other end of one wire to the Emergency Stop Wire, using a suitable Electrical Connections for Outboard Use insulated wire connecting device, Only reference Wire Color Table and Diagram B. THIS INTERRUPT SWITCH IS DESIGNED FOR USE WITH . . . . $%. . OUTBOARD MOTORS EQUIPPED WITH GROUNDING TYPE EMERGENCY . . . . . . STOP CIRCUITS ONLY! . . ,. . . . . . . 1% If the following information is not correct for your #". % . . . . model motor or application, consult your local . 223 /. marine dealer for details. . . . #. 1. Disconnect all batteries and any auxiliary on-board or dockside power supplies. 2. Remove Engine Cover. Locate the correct color emergency stop wire for your motor (reference Table 1). 8#%-'$%%#7575$+,#"181%%. #. . . . . . %9. . . . . #. Page 3 of 4 Pages 055001-695 Rev. C 10/03 © 2003 Teleflex, Inc. 8. Attach the other end of the second wire to Operating Instructions the ground point, using a suitable insulated wire connection device as shown in Diagram B. 9. Recheck all connections. Install the Lanyard with the Fork Clip seated over the Plunger. 10. Replace engine cover. 11. Reconnect battery. 12. Start engine. If engine does not start: Disconnect battery, remove engine cover, recheck all electrical connections, replace cover and restart engine.. 13. Remove Lanyard. Engine should stop immediately. IF ENGINE FAILS TO STOP, RECHECK ALL WIRING. SHOULD THE ENGINE FAIL TO START OR STOP, OR RESUMES RUNNING WITH THE LANYARD FORK REMOVED, CONSULT YOUR LOCAL MARINE DEALER FOR ASSISTANCE. Installation Notes ALL WIRING. CONNECTIONS AND TERMINATIONS should be done in accordance with ABYC Spec. E-9-90. Use 16 AWG Purple stranded insulated marine quality wire for I/0 or Inboard applications. (Type HDT, THW, UL 1426 or equivalent.) Use 16 AWG Black stranded insulated marine quality wire for all outboard applications. (Type HDT, THW, UL 1426 or equivalent.) 6980 Professional Parkway East Sarasota, FL 34240 (941) 907-1000 FAX (941) 907-1020 1. Before each motor start. check that the Lanyard Fork Clip is properly seated over the switch and rotates freely. Inspect the Lanyard. If it is cut. worn or frayed. it must be replaced. . . . 2. . . 1. . . 1. '. 5. + 2. The Lanyard Snap Hook should be securely attached to the operatoris body. Do not attach the Hook to a belt loop or button hole as these lack the strength to assure proper Switch operation. 3. Start the engine. 4. Test the Switch by pulling the Lanyard Fork Clip free from the Switch. IF ENGINE FAILS TO STOP, RECHECK ALL WIRING. SHOULD THE ENGINE FAIL TO START OR STOP, OR RESUMES RUNNING WITH THE LANYARD FORK REMOVED, CONSULT YOUR LOCAL MARINE DEALER FOR ASSISTANCE. DO NOT USE ANOTHER MANUFACTURERiS LANYARD ON THIS INTERRUPT SWITCH, OR CHANGE THE LENGTH OF THE LANYARD AS THIS MAY AFFECT SWITCH OPERATION. MISUSE, MISAPPLICATION, UNAUTHORIZED MODIFICATIONS, OR INCORRECT INSTALLATION OF THIS SAFETY DEVICE COULD RESULT IN SERIOUS BODILY INJURY OR DEATH. 055001-695 Rev. C 10/03 © 2003 Teleflex, Inc. Page 4 of 4 Pages ...

Herunterladen

Geben Sie zwei Ziffern: