Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Kenwood Dateigröße: 387.87 kb Dateiname: Unterrichtssprache:

FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming. Note: This function is available only in Conventional FM Operation. KEY FUNCTIONS Key Function Selcall or Selcall + Status Press to change the transceiver mode as shown in the diagram below. CH control Rotate to select an ID from the pre-programmed ID list or Status list. PTT switch or PF4 key Press to initiate a call. Keypad 0 ~ 9 Use the DTMF keypad to enter Selcall or Status numbers. PF1 or keyDTMF Press to exit Selcall or Status mode. Selcall Mode 1 Status Mode 2 Stack ModeNew Message Display Mode Normal Operating Mode Press PF2 Press Selcall or Selcall + Status or receive a Selcall Receive a new message Press any key Hold Selcall, Status or Selcall + Status Press PF1 Press PF1 or 1 Depending on how your dealer programmed the transceiver, Selcall mode may be skipped or the transceiver may exit Selcall mode automatically (as shown by the dash arrow). 2 After entering Selcall mode by pressing the Selcall + Status key, you can enter Status mode by pressing the PF2 key. 17 SELCALL (SELECTIVE CALLING) A Selcall is a voice call to a particular station or to a group of stations. ¦ TRANSMITTING 1 Select your desired zone and channel. 2 Press the key programmed as Selcall or Selcall + Status to enter Selcall mode. 3 Press the GRP and keys or rotate the CH control to select the ID of the station you want to call. . Alternatively, you can enter a station ID using a DTMF keypad. 4 Press the microphone PTT switch and begin your conversation. • Alternatively, you can press the PF 4 key to page the selected station, rather than making a voice call. ¦ RECEIVING An alert tone will sound, the transceiver will automatically enter Selcall mode, and the calling station.s ID will appear when a Selcall is received. To respond to the call, press the microphone PTT switch and speak into the microphone. ¦ IDENTIFICATION CODES An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number. Each transceiver must have its own Fleet and ID number. . Enter a Fleet number (100 ~ 349) to make a group call. . Enter an ID number (1000 ~ 4999) to make an individual call in your fleet. . Enter a Fleet number make a call to all units in the selected fleet (Fleet call). . Enter an ID number to make a call to the selected ID in all fleets (Supervisor call). . Select .ALL. Fleet and .ALL. ID to make a call to all units (Broadcast call). Note: The ID range may be limited by programming. STATUS MESSAGE You can send and receive 2-digit Status messages which may be decided in your talk group. Messages can contain up to 16 alphanumeric characters. Status messages range from 10 to 99 (80 ~ 99 are reserved for special messages). A maximum of 15 received messages can be stored in the Stack memory of your transceiver. These saved messages can be reviewed after reception. Depending on your dealer settings, when the Stack memory is full, either the oldest message will be erased when a new message is received or the new message will not be stored in the Stack memory. • The (KCH-14) or (KCH-15) icon appears when a message is stored in the Stack memory. 18 ¦ TRANSMITTING 1 Select your desired zone and channel. 2 Press the key programmed as Status to enter Status mode or Selcall + Status to enter Selcall mode. • When using the Status key to enter Status mode, the target Fleet/ ID is fixed and cannot be selected. Skip to step 5 to continue. 3 In Selcall mode, press the GRP and keys or rotate the CH control to select the ID of the station you want to call. . Alternatively, you can enter a station ID using a DTMF keypad. 4 Press the PF 2 key (the second key from the left, after the CH control), to enter Status mode. 5 Press the GRP and keys or rotate the CH control to select the status ID you want to transmit. . Alternatively, you can enter a station ID using a DTMF keypad. 6 Press the microphone PTT switch or the PF 4 key to initiate the Status call. . .. is displayed when the call has been successfully transmitted. ¦ RECEIVING The (KCH-14) or (KCH-15) icon will flash and a calling ID or text message will appear when a Status call is received. Press any key to return to normal operation. ¦ REVIEWING MESSAGES IN THE STACK MEMORY 1 Press and hold the key programmed as Selcall, Status, or Selcall + Status for 1 second to enter Stack mode. . The last received message is displayed with the message number. 2 Press the GRP and keys or rotate the CH control to select the desired message. 3 Press the PF 1 key to return to normal operation. .To delete the selected message, press the PF 3 or DTMF # key. To confirm the deletion, press the PF 2 or DTMF key. .To delete all messages, press and hold the PF 3 or DTMF # key for 1 second. To confirm the deletion, press the PF 2 or DTMF key. 19 SHORT MESSAGES To send a short message, you must connect the transceiver to a PC. Ask your dealer for details. • Short messages can contain a maximum of...

Herunterladen

Geben Sie zwei Ziffern: