Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Kenwood Dateigröße: 12.16 mb Dateiname: Unterrichtssprache:

The F indicator will illuminate. 3. Press the |0 I key within 5 seconds. The selected memory channel number will flash as an indication the Memory Channel has been locked out. NOTE:- The channel number will not flash while the display is showing M and the listing of the memory channels that contain data. It will only flash when you recall the individual memory channel from the front panel directly. 4. To cancel the lockout press the desired memory channel number key and then press the lF and |0 I keys again. 2. Press the F will illuminate. key. The F indicator • CLEARING A SPECIFIC MEMORY CHANNEL 1. Press the Im I key. The display will indicate M and any memory channels that contain data. (Ex. 1, 4, 5, 7, 8, 9) □ □ 0 BEDS M □ □ 0 BEDS F M 16 3. Press the key that corresponds to the channel you want to clear (Ex. 7) within 5 seconds of pressing the I f 1 key. The M, F, and channel number display will clear indicating the operation has been completed. 4. To confirm the data was erased press the 1M | key. (From our example the Q will now be gone.) • CLEARING ALL MEMORIES (= Microprocessor Initialization) To erase all data from the memories, turn the power switch on while pressing both the If and the enter ] keys together. • MEMORY BACK-UP BATTERY The transceiver includes a lithium back-up battery to retain memory in the microprocessor. When changing batteries, or if the Ni-Cd batteries should fully discharge, memory will always be retained. If the display should begin to show erroneous information or numbers, the lithium battery needs replacement. This should be performed by an authorized KENWOOD dealer since these components are easily damaged by static electricity. ■ PRIORITY ALERT CHANNEL CHECK Memory channel 1 can be monitored at about 5 seconds intervals to check for activity. □ □ 0 00 M Press the _f_ key and then the 1/PRIO key, I prio I will appear on the display. If the channel is busy, the PRIQ indicator blinks, and if the BEEP function is ON, a beep will sound. To stop the function, press the E and 1/PRIO keys again. The function does not operate during scan or transmission. ■ BATTERY SAVER Battery Saver operation provides to turn ON or OFF battery power automatically during reception and thus extend operation time. 2 ACTIVATION MODES 1. SAVE MODE: The transceiver will activates the battery saver circuit 2 seconds after the squelch closes. 2. AUTO SAVE MODE: The transceiver will activates the battery saver circuit 1 minute after the last key operation during the squelch closes. To select the desired Battery Saver Mode, press the save key. Each time press the key, radio will advance from SAVE to AUTO SAVE to OFF. The indicator will light; SAVE MODE : /Save] AUTO SAVE MODE : I auto/ /Save I OFF : No indicator Power Save Ratio Selection To alter the actual length of time the receiver section shuts down, press the fF I key and then the save key. The display will show the time the radio will be operating at reduced power levels (Ex. 1 Use the > or the ▼ key to select the desired save ratio from 1 : 1 to 1 : 9. Press the enter key to complete the selection. The radio will operate at reduce power consumption according to the accompanying diagram. For example; M"",means ON OFF [-2.-1 means f~| . I I , I~1 [~1 ON 0FF [-9.—] means ±?0.3 sec When a signal is received, the function is automatically cancelled. Since the receiver section shuts down, the squelch may not open by pressing the MONITOR switch. n n : 1). IAUTO//SAVEI _ I__ I . 17 MAINTENANCE ■ IN CASE OF DIFFICULTY WHEN USING SUM-3/AA BATTERIES, ENSURE THE BATTERY POLARITY AND VOLTAGE IS CORRECT BEFORE PROCEEDING. No sound from the speaker. No signal can be received. 1. Squelch is closed. Turn the SQL control counterclockwise. 2. T.SQ is activated. Turn the SQL control clockwise past the detent position. 3. PTT switch of microphone is pressed setting the unit in the transmit mode. Turn PTT switch off. No control works. KEY LOCK is ON. Press IF I key and KEY LOCK key. No output 1. Microphone jack is not fully plugged in. Insert the plug ' fully. 2. Poor antenna connection. Connect antenna securely. Memory loss. Backup battery voltage is low. Contact your authorized dealer. All the indicators go out on the display. Turn the power switch OFF and then ON. The and/or i on air indicator begins to blink. The [jQfl indicator will come on when the battery needs recharging. If you continue to operate and the |jy|| and/or [onairI indicator begins to blink the radio will no longer operate properly. _ Replace/Recharge the battery when the indicator comes on. 18 ■ SERVICE Should it ever become necessary to return the equipment to your dealer or service center for repair, pack in its original box and packing, and include a full description of the problems involved. Also include your telephone number. You need not return accessory items unless directly related to the service problem. Se...

Herunterladen

Geben Sie zwei Ziffern: