Stimmen - 6, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
2 Nautical Mile visibility. CAUTION: Read all instructions carefully before installing and using this product. All positive (+12V DC) lighting wires require a 1-amp fuse to protect circuits and vessel. The aluminum light pole is not grounded. MAKE SURE POWER SOURCE IS 12-VOLT DC ONLY. HIGHER VOLTAGE WILL DAMAGE LIGHT AND CIRCUITRY. WARNING To prevent injury, disconnect power when installing or servicing this product. Remove boat from water before using 120V power tools. REQUIRED FOR INSTALLATION • Cordless drill; 1/8" and 3/8" (3 and 10mm) bits • Marine-grade non-silicone sealant • Phillips screwdriver • Two #10 pan head stainless steel screws • 3-position switch (OFF/ON/ON) • Fuse holder and fuse: 1-amp • 16-gauge wire • Appropriate marine-grade wire connectors LED Anti-Glare All-Round Lights are designed for boats up to 39.4 feet (12m). It provides 360 degree controlled light output and 2-mile visibility while shielding the driver from on-board glare (Figure 1). Position the All-Round Light so its bulb is not less than one meter (39.4") above sidelights. If replacing an existing pole light, replace with a pole at least as long as the existing pole. Mount the anti-glare light in a position so that: • Light output is fl at and parallel to water when boat is fl oating. • Light shines 360°, unobstructed. • Light does not shine on operator, or refl ect off any part of the boat in the operator’s fi eld of vision. Figure 1 Figura 1 One meter or 39-3/8" 39 3/8 po(un metre) 39-3/8" (un metro) INSTALLATION INSTRUCTIONS Bases are available for mounting on vertical or horizontal surfaces. Release the cam-lock adjustment handle to fold light or adjust to vertical position. Change Base Type (If Required) on Fold-Down Base Packaged versions of the light are shipped with the horizontal base installed. To switch to the vertical base: 1. Carefully remove the cam-lock screw and oblong washer. Set aside for reinstallation (Figure 2). Figure 2 Figura 2 STEP 1 ETAPE 1 Vertical Base Base verticale STEP 3 ETAPE 3 PASO 3 Socket PASO 1 STEP 2 ETAPE 2 PASO 2 Horizontal BaseBase horizontaleBase horizontal Cam-lock Screw and Oblong Washer Vis de serrage et rondelle oblongue Tornillo con leva de fijacion y arandela alargada Douille Portalamparas Axle Axe Eje Base vertical Feed Wires Thru Inserez les fils a travers Pasar los cables 2. Pivot the base axle out of its socket. Note position of the 2 wires in the base slot. Remove the horizontal base. 3. Insert wires through slot of the vertical base. Reassemble in reverse order. Mark Position for Fixed Base Light, (Figure 3) 1. Place light in selected position. 2. Using the base as a template, mark the two mounting hole locations and one wire access hole. Proceed to “Install Light” below. Figure 3 Figura 3 Mark Position for Fold-Down Light 1. Release cam-lock adjustment handle and adjust light to vertical position. (Figure 4) 2. Place light in selected position. 3. Use optional adaptors, if necessary, to allow installation on angled windshields. 4. Using the base as a template, mark the two mounting hole locations and one wire access hole. (Figure 5) Proceed to “Install Light” below. Figure 4 Locked Optional DeverrouilleVerrouille Trabado Unlocked Adaptor Destrabado Adaptateur en option Adaptador opcional Figure 5 Locked Verrouille Trabado Optional Unlocked Adaptor Deverrouille Adaptateur Destrabado en option Adaptador opcional Install Light CAUTION: Position wire access hole carefully, especially on aluminum boats, so that wires do not contact the hull. 1. Remove light from marked position. Drill two 1/8" (3mm) pilot holes for #10 screws. Drill one 3/8" (10mm) wire access hole. 2. Bring the two 16-gauge wires up through access hole. 3. Use marine-grade waterproof crimp connectors to connect gray wire to positive lead from 3-position switch. Connect (-) negative source to black wire and route to (-) negative terminal on battery. 4. Fasten light to deck with two #10 stainless steel pan head screws. DO NOT OVERTIGHTEN. Base Wiring IMPORTANT: LED-based lights MUST be wired for correct polarity. NOTE: Do not use light pole as a fl agpole or handle. OPERATION After installation, check lights to verify proper operation. Regulations require lights to be operated with a three-position switch for: 1. Running lights (sidelights and all-round light); 2. Anchor lights (all-round light only); 3. Off. ATTWOOD LIMITED 10-YEAR WARRANTY Because of the longevity of Attwood’s LED lighting technology, Attwood offers a limited 10-year warranty on this LED lighting product. See Product Catalog or attwoodmarine.com for details. © 2007 Attwood Corporation 1016 N. Monroe Street, Lowell, MI 49331-0260 Figura 4 Horizontal Mount Montage horizontal Montaje horizontal Figura 5 Vertical Mount Montage vertical Montaje vertical Lumiere visible sur tout l’horizon Lumieres a base fi xe et rabattable antirefl et a DEL serie 5550 Directives d’installation CONSERVEZ CES DIRECTIVES Formulaire n° 69428 Rev....