Login:
Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Anleitung Attwood, modell 3530

Hersteller: Attwood
Dateigröße: 63.95 kb
Dateiname: 69425-a-led-sidelight-install.pdf
Unterrichtssprache:enfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Meets USCG CFR 183.810, ABYC A-16 requirements and all applicable standards as tested by Imanna Laboratories, on 2/22/2007. 1 nautical mile visibility. 2NM Bi-Color Combination Bow Light For boats up to 20 meters / 65.6 feet. Meets USCG CFR 183.810, ABYC A-16 requirements and all applicable standards as tested by Imanna Laboratories, on 3/6/2007. 2 nautical mile visibility. 2NM Sidelights For boats up to 50 meters / 164 feet. Meets USCG CFR 183.810, ABYC A-16 requirements and all applicable standards as tested by Imanna Laboratories, on 3/6/2007. 2 nautical mile visibility. REQUIRED FOR INSTALLATION • Phillips screwdriver • Drill and bits: 3/8" for wire clearance hole • Pilot drill for mounting screws • Two #10 pan head stainless steel screws (not included) LOCATION 1. Position light(s) on a surface of the gunwale or deck that is horizontal (within +/-5 degrees). 2. When installing bicolor combination light, place it on the centerline of the boat at the bow (See Figure 1a). When installing sidelight pairs, place lights with the red lens on the port (left) and green lens on the starboard (right) as you stand onboard facing bow of the boat. Lights must be parallel to centerline of the boat (See Figure 1b). Figure 1a Figure 1b Red Green (Port) (Starboard) Red Green (Port) (Starboard) 3. Make sure there are no obstructions at the front or side (such as rail stanchions, chocks, anchors, cleats, etc.) within the light’s arc of visibility (112.5 degrees each side). 4. Measure and mark location of wire clearance hole. At the marked location(s), make a mark for a 3/8” hole. (See Figure 2). • If installing a bicolor light, location must be on the boat centerline. • If installing a sidelight pair, both mounting holes must be the same distance from the bow. DRILLING INSTRUCTIONS 1. Remove the cover and housing by removing the Phillips-head screw in the cover and lifting off. (See Figure 2). 2. Assemble gasket to base. Cover Screw Stainless Steel Lens Cover Telltale Post Housing Vertical Tab, Aligned with Boat Centerline Mounting Screw Base Base Tabs Gasket Butt-Joint Connectors 3/8" Hole, Aligned with Boat Centerline 3. Align hole beneath light base with the position you’ve marked for the wire clearance hole. Set the lamp toward the bow and align vertical tab with the boat centerline. 4. Use the light base as a template to mark locations for the mounting screw pilot holes (use 2 #10 stainless steel screws). CAUTION Position holes carefully on aluminum boats so that wires do not contact the hull. 5. Drill wire clearance hole and pilot holes for the mounting screws. MOUNTING INSTRUCTIONS 1. Be sure gasket is aligned with the base. 2. Insert two #10 stainless steel mounting screws through base and fasten base to the deck. Tighten until gasket seals to the deck. NOTE If area below the light will not be reachable after installation, attach a suitable length of 16-gauge red- and black-colored NON-POWERED wire that can be routed to an accessible area. Make connecti...

Dieses Handbuch ist für folgende Modelle:
Boote Zubehör - 3500 Series (63.95 kb)
Boote Zubehör - 3520 (63.95 kb)
Boote Zubehör - 3540 (63.95 kb)
Boote Zubehör - 3550 (63.95 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien