Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Qty Remarks Conversion Cable 02S4147 000-141-082 1 For water temperature and spd/temp sensors Water Temperature & Speed Sensor ST-02MSB 000-137-986 1 Thru-hull type ST-02PSB 000-137-987 Water Temperature T-02MTB 000-040-026 1 Transom mount, w/8 m cable T-02MSB 000-040-040 Thru-hull mount T-03MSB 000-040-027 Thru-hull mount, w/8 m cable Inner Hull Kit S 22S0191 000-802-598 1 Matching Box MB-1100 000-041-353 1 For connection to 1 kW transducer For FCV585 Transducer 50B-6 000-015-042 1 10 m, 1 kW 50B-6B 000-015-043 15 m, 1 kW 200B-5S 000-015-029 10 m, 1 kW 50/200-1T 000-015-170 10 m, 1 kW viii 1 1. OPERATION 1.1 Control Description Display unit for FCV-620 Note: The FCV-620 and FCV-585 share the same features. For sake of brevity, this manual uses “FCV-620”. How to remove the hard cover Place fingers below cover, pull cover forward and lift it. When removing the display unit To keep out dust from connectors: - Cover transducer cable’s connector with MJ cable cap (supplied). - Cover two connectors on display unit with their caps. - Cover power cable’s connector with its cap. No. Control Function 1 MENU/ESC • Opens/closes menu. • Escapes from current operation. 2 ........ (TrackPad) • Moves cursor on the menu. • Adjusts settings. • Moves VRM (Variable Range Marker) by using .. or .. except for nav mode. 3 ENTER Saves settings. 4 RANGE Opens display range setting window. 5 MARK Records the position of an important echo as waypoint. (Outputs latitude and longitude position to a plotter.) 6 FUNC Opens user defined window. 7 GAIN • Push: Opens automatic gain setting window. • Rotating: Manually adjusts gain (with automatic gain adjustment off). 8 MODE Selects display mode. 9 /BRILL • Turns power on/off. • Opens display contrast/brilliance setting window. (The FCV-585 does not have the contrast function.) GAIN 0 10 2 8 4 6 FCV-620 MENU/ESC ENTER RANGE MARK FUNC MODE BRILL AUTO NAV1 ZOOM LF DUAL HF ZOOM NAV2 1 9 2 3 4 5 6 7 8 1. OPERATION 1.2 Power On/Off 1. Press the /BRILL key to turn on the power. The unit beeps, the startup screen appears, and then the equipment checks the ROM and RAM for proper operation. After the completion of the equipment check, the last-used display appears. Startup screen 2. To turn off the power, press the /BRILL key more than three seconds. The time remaining until power is turned off is counted down on the screen. Note1: If "ROM/RAM check error!" appears, try to press any key except the /BRILL key to start operation. However, the equipment may not work properly. Contact your dealer. Note2: The first time you turn on the power (or any time the power is applied after a memory reset), the installation menu appears. See the figure below. When this occurs, press the MENU/ESC key twice to close the menu. Language : English Depth Unit Temp Unit Speed Unit Wind Unit Distance Unit Demonstrate ../..: Select [ENTER] : Enter [MENU] : Quit Installation Francais Espanol Deutsch Italiano Portugues Dansk Svenska Norsk Suomi , . English Installation menu 1.3 Adjusting Display Contrast and Brilliance 1. Press the /BRILL key momentarily to show the contrast/brilliance adjustment window. (The FCV-585 does not have the contrast function.) Contrast/Brill • Min Max • Contrast 5 Brill 9 ../.. : Select [ENTER] : Set [MENU] : Cancel Contrast/brilliance adjustment window 2. To adjust brilliance, press the /BRILL key. Continual pressing changes the brilliance continuously (0>1>...>9>8>...>0> 1>...). “0” is the dimmest and “9” is the brightest. After selecting “Brill” by using .. or .., you may also use .. or .. to adjust brilliance. 3. To adjust contrast, after selecting “Contrast" by using .. or .., use .. or .. (only for FCV620). “0” is the lowest and “9” is the highest. 4. Press the ENTER key to save the setting and close the window. Note: When the power is reapplied after turning off the equipment with minimum brilliance, minimum brilliance will be set after the equipment goes through its initial start up. (The start up screen appears with the maximum brilliance.) Adjust the brilliance as necessary. 1.4 Choosing a Display Mode 1. Rotate the MODE knob to open the mode setting window, which is displayed for five seconds. NAV1 LF-ZOOM LF DUAL HF HF-ZOOM NAV2 MODE Nav data mode 1 Low frequency zoom mode* Low frequency mode (50 k) Dual frequency mode High frequency mode (200 k) High frequency zoom mode** Nav data mode 2 *: The indication at the top on the screen is B/L-LF, B/Z-LF or M/Z-LF. **: The indication at the top on the screen is B/L-HF, B/Z-HF or M/Z-HF. B/L: Bottom lock, LF: Low frequency, B/Z: Bottom zoom, HF: High frequency, M/Z: Marker zoom 2 1. OPERATION 3 2. Rotate the MODE knob again to choose the display mode desired. The screen you chose appears soon thereafter. Single frequency display Low frequency (50 kHz) The sounder uses ultrasonic signals to detect bottom conditions. The lower the frequency of the signal, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detec...