Products that are replaced or for which a refund is issued become the property of Attwood. THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY OF THIS PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE (1) YEAR FROM THE DATE OF ORIGINAL CONSUMER PURCHASE. ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or

Position pump in the lowest accessible part of the bilge. On sailboats, location should be centered over keel. (Figure 1) Thru-Hull Connector Hose & Clamp Hose MUST Rise Upward with NO DIPSuitable Mounting Pad Base Strainer 12" min. Above Water Line 2. Do not mount pump directly to hull. Attach base strainer to a marine plywood mounting pad that is fiberglassed to the hull. HOSE CONNECTION INSTRUCTIONS IMPORTANT: To prevent airlock, hose must rise continually upward to the thru-hull connector wi

The Boat Trailer Guide Protectors simply slide on and fit tightly on the existing guide poles. The Boat Trailer Guide Protectors are designed to float up with the water height to help guide you on boat ramps with steep angles. Available in 4 sizes and a wide variety of colors! PART NUMBERS AND SPECIFICATIONS I.D. Length Color Aftermarket Packaging* 2" I.D. 36" Black 105693BK 2.5" I.D. 36" Black 105694BK Forest Green 105694FG Navy 105694NV Red 105694RD Royal 105694RB Silver 105694SV 48

4. Replace base. Attach with #8 stainless steel fasteners. 5. Re-attach pump to base. Insert into base, twist clockwise until tab snaps in and prevents turning. (Figure 2) WIRING INSTRUCTIONS Make all wire connections above the highest water level. Use marine grade wire connectors only. Waterproof all connections with suitable materials. (Figure 3) NOTE: Failure to make waterproof connections and fuse pump properly will void the product warranty. Figure 3 (neg) (pos) 2-Terminal On/Off Switch Bro

Determine which direction you want pump outlet fitting to point after installation. Mark pump base and mounting pad in desired position. If Automatic Float Switch is to be installed, allow enough room on pad for shim and switch. 2. Remove pump base from motor housing by depressing lock button and twisting clockwise. 3. Align base with pad at marks, and fasten with four #8 screws. 4. Attach pump to base by aligning four retaining tabs and twisting counterclockwise until the lock button snaps into

The Boat Trailer Guide Protectors are designed to float up with the water height to help guide you on boat ramps with steep angles. Available in 4 sizes and a wide variety of colors! PART NUMBERS AND SPECIFICATIONS I.D. Length Color Aftermarket Packaging* 2" I.D. 36" Black 105693BK 2.5" I.D. 36" Black 105694BK Forest Green 105694FG Navy 105694NV Red 105694RD Royal 105694RB Silver 105694SV 48" Black 105695BK Forest Green 105695FG Navy 105695NV Red 105695RD Royal 105695RB Silver 10

Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69291 Rev. B 03-10 Application Designed to work on traditional tank vent systems with standard ..." (16mm) I.D. vent hose, the In-Line Fuel Surge Protector Installs: • Directly into the vent hose above the top of the gas tank and 10" to 12" (254mm to 305mm) below the external vent. • At a position within 45° of vertical so that the arrow with the word VENT points upward toward the boat’s ext

Press trim plate onto switch, verify correct operation. Peel paper backing from trim plate, push plate firmly against mounting surface. Figure 1 Figure 2 © 2003 Attwood Corporation 1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

The Boat Trailer Guide Protectors simply slide on and fit tightly on the existing guide poles. The Boat Trailer Guide Protectors are designed to float up with the water height to help guide you on boat ramps with steep angles. Available in 4 sizes and a wide variety of colors! PART NUMBERS AND SPECIFICATIONS I.D. Length Color Aftermarket Packaging* 2" I.D. 36" Black 105693BK 2.5" I.D. 36" Black 105694BK Forest Green 105694FG Navy 105694NV Red 105694RD Royal 105694RB Silver 105694SV 48

Length Color Aftermarket Packaging* 2" I.D. 36" Black 105693BK 2.5" I.D. 36" Black 105694BK Forest Green 105694FG Navy 105694NV Red 105694RD Royal 105694RB Silver 105694SV 48" Black 105695BK Forest Green 105695FG Navy 105695NV Red 105695RD Royal 105695RB Silver 105695SV 60" Black 105696BK Forest Green 105696FG Navy 105696NV Red 105696RD Royal 105696RB Silver 105696SV Black Forest Green Navy Red Royal Blue Silver * Poly bag, pair ©2008 Attwood Corporation • 1016 N. Monr