Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Thanks for joining us. By purchasing the Holder@ 12, you are treating yourself to the ultimate in sailing enjoyment. Even if you have long experience with sailboats, please read this manual thoroughly. It will give you easy, accurate instructions on assembling your new boat. We suggest reading through the manual completely before you begin assembly. Pay special attention to the boat and parts descriptions shown on the following pages. If you are new to sailing, this manual will not teach you how to sail. There are many excellent courses and books available on the safe handling of small sailboats. Contact your Holder@ dealer or local Coast Guard Auxiliary for recommendations on courses in your area. They'll be happy to help. Please remember to obey the most important rule of all when assembling your boat -stay away from overhead power lines! Before starting to rig your boat, thoroughly examine the area for power lines and report any potentially hazardous power line that you see by writing to the reponsible utility company, send a copy to Hobie Cat Bounty Program, P.O. Box 1008, Oceanside, CA 92054 and sail elsewhere. Remember, CONTACT OF A .. MAST WITH A POWER LINE COULD BE FATAL. The Holder@ 12 is made with the innovative ComptipTM mast tip (U.S. Pat. No. 4,597,346). ; This is an essentially non-conducting composite tip which can help prevent electrocution and boat damage from mast/power line contact. Hobie Cat worked many years to develop this new tip so that it would be as effective as possible. Still, nothing can provide total protection at all times, so it's best to avoid wires. Be sure to read the "Maintenance" section to find out how to protect the tip's insulating ability. By following the instructions, maintaining your new boat properly and observing safety rules, we're confident you'll receive many years of sailing enjoyment from the Holder@ 12. -1~ HOLDER 12@ Terminology ~ .. MAST WINDOW OUTHAUL REARPIN BOOM TILLER EXTENTRAVELE BOOMBLOCKS MAIN SHEET DDWNHAUL VANGBECKETBLOCK VANGLINE VANGADJUSTERCLEAT HULL DAGGERBOARD '. i . WARNING Before starting assembly, be sure the area in which you plan to work is free from overhead power lines. Contact of a mast with a power line could be fatal. 1\ -2 1) Hull 2) PadEyewith Block 3) Mast Tube 4) Jam Cleat ! 5) UpperMastComptip@ ~,~ 6) Lower Mast ~.. ; 7) GooseneckAttachment [ Casting '-8b) MainSheetBlock 8a) Main SheetBlock with Becket 9) Boom 10) Gooseneck 11) Yang Block ~ = .- 6 CIJ ~ ~ ~~ < ~ CIJ ~ L.. ca c.. N . @ ~: u.J .. C -J .. C ::~ 12) Sail 13) Battens 14) Daggerboard 15) RudderAssembly 16)Mainsheet(5/16"x 35) 17) Halyard Line (1/4" x 34) 18) Outhaul Line (3/16"x 6) 19) Traveler Line (1/4" x 4) 20)DownhaulLine(3/16"x 8) 21) Twist Shackle 22) Tiller ExtensionConnector 23) YangBlock (Lower) 24) Traveler Block 25) CockpitDrain Plug 0 ~ I ~~-..~ Q) @ 26) Warranty Card,Manual 27) Tiller Extension 28) Hull Drain Plug 29) CockpitDrain Hole 30)Gudgeons 31) Hiking Straps 32) Main SwivelJam Cleat 33) Compass NOTE: Someparts shown may not bewith standard boats. -3 ASSEMBLY INSTRUCTIONS I. The Plugs The larger drain plug (part #25) is used to drain the cockpit of the boat. Insert the large t drain plug from the inside of the HOLDER@ 12 into the drain hole, which is in the center and bottom of the stern or rear of the boat (part . #29). Secure the plug by looping the line through the padeye as shown in Figure 1. Fig. 1 The smaller plug threads into the hole located on the exterior of the transom by the large. drain plug hole as shown in Figure.2. Be sure to use the black gasket to prevent leaks. (This may already be installed.) .. Fig. 2 .. II. Traveler Assembly Figure 3 shows an example of a completed traveler line and block assembly. To assemble the traveler, first find the traveler block set. This block has two pulleys (part #24). Now find the traveler line (part #19). Tie a figure 8 knot in one end of the line and insert the other end of the line', from the outside of the HOLDER@ , 12, through the small hole in the upper right- hand corner of the rear of the boat. F.g 3 1 . Pull the l~ne all the way through and then thread the lIne through t.he small block of the t:aveler block ~et: Now Insert the end of the lIne from the InsIde of the boat through the small hole at the upper left hand corner of the boat. Tie a figure 8 knot in the end of the line. Make sure the knots are secure and that the traveler block set can run freely along the line. -4 III. Mast and Sail Assembly A. Standard and Special Edition The mast is in two sections (part #'s 5, 6). The bottom section displays the warnings against sailing and assembling near overhead t wires and power lines. Before raising the mast, check again that you are in a safe area and always remember this warning. W Insert the top section of the mast into the bottom section, making sure the tab on the rib fits securely into the notch at the opening, as shown in Figure 4. Fig. 4 Next, find the three sail battens (part #1...