Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
2) Air tools can create dust when drilling, grinding, sanding or cutting. This dust can contain substances known to cause cancer, birth defect, etc. Also wear proper breathing protection. ) Do not wear loose clothing or jewelry, and ensure long hair is protected with a proper cover. 4) Do not exceed the maximum operating pressure of this tool or any component in the air delivery system. 5) Do not depress the trigger when connecting this tool to the air supply system. Always disconnect the tool from the air supply system when changing attachments. 6) Only use attachments specifically designed for use with air tools. Hand tool sockets can shatter and cause serious injury. Do not use worn or damaged attachments. Make sure attachments are securely attached to the air tool. 7) Do not point the air tool at yourself or any other person. 8) Never use Oxygen or combustible gases to operate this tool. Use only lubricated compressed air regulated to the recommended operating pressure for this tool. 9) Disconnect this tool from its air supply before attempting to install or change attachments or before attempting any service. Also disconnect the air tool from the compressed air system when not in use. 10) Excessive use of this tool can cause injury due to vibration and fatigue. Do not use this tool in awkward positions, and avoid repetitive work motions. When feeling discomfort, numbness, fatigue, tingling or pain stop work immediately and seek medical treatment and advice. 11) Inspect air hoses, and discard if in worn, weak or damaged condition. Make sure all air connections are tight and secure. 12) Keep hands away from moving parts 1 ) Consider working conditions and environment. Do not operate this tool around hazardous gases or flammable gases. Keep your work area neat and tidy and make sure the work area is well lit. 14) Always use clamping devices to hold all work securely in place, never use hands or other body parts for holding work. Both hands must be used to operate this air tool, enabling control and safety. 15) Do not use this air tool if intoxicated, if you are using drugs or medication causing drowsiness or if you are tired. 16) Do not leave this air tool unattended, and disconnect from the air delivery system when not in use. Children must be supervised in the proximity of any air tool or work area. 17) Follow air supply manufacturer’s recommendation for connection of regulators, filters and other accessories. Do not install quick couplers directly on air tool, it puts unnecessary strain on the air inlet threads, instead install a short length of air hose to the tool. Do not over tighten fitting connecting to the air tool; this could cause the housing to crack. Use Teflon tape or pipe sealant carefully to prevent excess from entering the air tool. Wear hearing protection. Wear eye protection. Read the instruction manual Wear respiratory protection. BEFORE USING THIS AIR TOOL To ensure long life be sure to oil the tool daily. Pour 4 drops of Eagle air tool (SEA 20 non detergent) oil into the air inlet, and then run the tool for a few seconds to clean. If tool is an impact wrench fitted with a “Zirc” grease fitting: The hammer mechanism of this tool also needs to be greased from time to time (depending on usage). The tool is equipped with grease fitting for this purpose; use this connection to re-grease the tool using Eagle impact wrench grease. PLEASE USE EAGLE SEA 20 NON DETERGENT OIL OPERATING INSTRUCTIONS Add oil throughout the day when using. We highly recommend use of an in-line mini oiler to accomplish this. Blow out air line to clear dirt and moisture. The air regulator knob can be used as a throttle if there is no other means of regulating air. Turn the knob all the way in and adjust outward until desired speed is reached. Hold the tool away from work when starting. Set it down on the work evenly and make the cut. When cut is completed, lift tool away from work before stopping the motor. Use only discs rated at 20000 RPM or higher. Accessory retainers should be used to prevent ejection of the accessory which might injure persons. EXCEPTION: Retainers need not be used if in compliance with acceptable safety codes. In such cases, to avoid injury, the trigger should never be depressed unless the accessory is held firmly against the work piece. Accessory should be removed when tool is not in use. TROUBLESHOOTING SYMPTOMS CAUSE REMEDY Air tool does not run or runs slow. Lack of lubrication. Lubricate as per instructions. Dirt in tool. Clean with mixture of 50/50 tool oil/solvent. Lubricate after cleaning. Insufficient air pressure. Check regulator and air supply for leaks. Check compressor to make sure it operates at correct pressure. Make sure air hose is properly sized and that multiple hoses are not connected to same outlet. Check air hose for leaks and repair. Rotor blades worn or motor bearing worn or dirty. Replace blades, inspect clean or replace bearing. IMPACT WRENCH does not impact or impact...