Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Note: Advises you of additional information concerning the operation or maintenance of the equipment. 5 SPECIFICATIONS Input .................................................................................................................. 120 Volts, 60 Hz, AC Only, 9.0 amperes No load speed ............................................................................................................................................... 0-2800 /min. Stroke Length......................................................................................................................................1 1/8 in. (28.6 mm) Switch ...................................................................................................................................................... Variable Speed ELECTRICAL DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool's internal insulation. Observe all normal safety precautions to avoid electrical shock. Important: Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest authorized service center for repair. Always use original factory replacement parts when servicing. ELECTRICAL CONNECTION This Saw has a precision-built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If your tool does not operate when plugged into an outlet, double-check the power supply. EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used. When working outdoors with a tool, use an extension cord that is designed for outside use. This type of cord is descignated with "WA" on the cord's jacket. Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation. **Ampere rating (on tool faceplate) 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0 Cord Length Wire Size (A.W.G.) 25' 50' 100' 16 16 16 16 16 16 16 16 14 16 14 12 14 14 10 14 12 — **Used on 12 gauge - 20 amp circuit. CAUTION: Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool. WARNING: Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. 6 UNPACKING INSTRUCTIONS When unpacking the tool: • Carefully remove the tool and accessories from the box. • Make sure that all items listed in the packing list are included. • Inspect the tool carefully to make sure no breakage or damage occurred during shipping. • Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. • If any parts are damaged or missing, please call 1-866-539-1710 for assistance. PACKING LIST 1 1/8 in. (28.6 mm) Stroke Variable Speed Saw Saw Blades (3) Hex Key Operator’s Manual Case APPLICATIONS WARNING: If any parts are missing do not operate your tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. WARNING: This saw should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury. You may use the reciprocating saw for the purposes listed below: • Cutting all types of wood products (lumber, plywood, paneling, composition board, and hard wood). • Cutting masonite and plastic. • Cutting drywall. • Cutting metals such as sheet steel, pipe, steel rods, aluminum, brass, and copper. 7 FEATURES Before using this tool, familiarize yourself with all operating features and safety requirements. However, do not let familiarity with the tool make you careless. Your new saw is equipped with the following features. See Figure 1. TOOLLESS BLADE CLAMP Your saw has a blade clamp design that does not require the use of a tool...