Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Model and serial number may be found at the rear of the base. You should record both model and serial number in a safe place for futu re use. CAUTION-. Read GENERAL and ADDITIONAL SAFETY INSTRUCTIONS CRRFTSHRHo 12-INCH MOTORIZED TABLE SAW • assembly • operating = repair parts Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U_S.A. Part No. 62597 L_ ;_,,,: FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAWS If within one year from the date of purchase, this Craftsman Table Sae fails due to a defect in material or workmanship, Sears will repair it, free of charge. Warranty service is available by simply contacting the nearest Sears store or Service Center throughout the United States. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO. BSC 41-3 SEARS TOWER CHICAGO, IL 60684 GENERAL SAFETY iNSTRUCTiONS FOR POWER TOOLS 1. KNOW YOUR POWER TOOL 13. SECURE WORK Read the owner's manual carefully. Learn its Use clamps or a vise to hold work when practical. It's application and limitations as well as the specific safer than using your hand, frees both hands to operate tool. potential hazards peculiar to this tool. 14. DON'T OVER REACH 2. GROUND ALL TOOLS This tool is equipped with an approved 3-conductor Keep proper footing and balance at all times. cord and a 3-prong grounding type plug to fit the 15. MAINTAIN TOOLS WITH CARE proper grounding type receptacle. The green conductor in the cord is the grounding wire. Never connect the Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changi ng accessories, green wire to a live terminal. 3. KEEP GUARDS IN PLACE in working order, and in proper adjustment and 16. DISCONIklECT TOOLS alignment. before servicing; when changing accessories such as 4. REMOVE ADJUSTING KEYS blades, bits, cutters, etc. AND WRENCHES 17. AVOID ACCIDENTAL STARTING Form habit of checking to see that keys and adjusting Make sure switch is in "OFF" position before plugging wrenches are removed from tool before turning it on. in. 5. KEEP WORK AREA CLEAN 18. USE RECOMMENDED ACCESSORIES Cluttered areas and benches invite accidents. Floor Consult the owner's manual for recommended must not be slippery due to wax or sawdust. accessories. Follow the instructions that accompany 6. AVOID DANGEROUS ENVI RONMENT the accessories. The use of improper accessories may Don't use power tools in damp or wet locations or cause hazards. expose them to rain. Keep work area well lighted. Provide adequate surrounding work space. 19. NEVER STAND ON TOOL Serious injury could occur if the tool is tipped or if the 7. KEEP CHI LDREN AWAY cutting tool is accidentally contacted. All visitors should be kept a safe distance from work area. Do not store materials above or near the tool such that it is necessary to stand on the tool to reach them. 8. MAKE WORKSHOP KID-PROOF -- with padlocks, master switches, or by removing 20. CHECK DAMAGED PARTS starter keys. Before further use of the tool, a guard or other part that 9. DON'T FORCE TOOL is damaged should be carefully checked to ensure that it It will do the job better and safer at the rate for which will operate properly and perform its intended function. it was designed. Check for alignment of moving parts, binding of moving 10. USE RIGHT TOOL parts, breakage of parts, mounting, and any other Don't force tool or attachment to do a job it was not conditions that may .affect its operation. A guard or designed for. other part that is damaged should be properly repaired 11. WEAR PROPER APPAREL or replaced. Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches) to get caught in moving parts. 21. DIRECTION OF FEED Nonslip footwear is recommended. Wear protective Feed work into a blade or cutter against the direction hair covering to contain long hair. Roll long sleeves of rotation of the blade or cutter only. above the et bow. 12. USE SAFETY GOGGLES (Head Protection) NEVER LEAVE TOOL RUNNING Wear Safety goggles (must comply with ANS Z87.1) at 22. UNATTE NDED all times. Also, use face or dust mask if cutting operation is dusty, and ear protectors (plugs or muffs) Turn power off. Don't leave toot until it comes to a during extended periods of operation. complete stop. ADDiTiONAL SAFETY iNSTRUCTiONS FOR TABLE SAWS WARNING: FOR YOUR OWN SAFETY, DO NOT OPERATE YOUR SAW UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS ... AND UNTIL YOU HAVE READ AND UNDERSTOOD THE FOLLOWING. 1. GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS ... SEE PAGE 2 2, GETTING TO KNOW YOUR SAW ... SEE PAGE 14 3. BASIC SAW OPERATION... SEE PAGE 17 4. ADJUSTMENTS... SEE PAGE 23 5. MAINTENANCE... SEE PAGE 26 6. STABI LITY OF SAW If there is any tendency for the saw to tip over or move during certain cutting operations such as cutting extremely large heavy panels or long heavy boards, the saw should be bolted down. If you attach any kind of table ex...