Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Model and sedal numbers may be found on the left rear side of the base, You should record both model and serial number in a safe place for future use, FOR YOUR READ ALL INSTRUCTIONS CAREFULLY ® 10 iNCH DIRECT DRIVE TABLE SAW -assembly . operating o repair parts J Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U_S,A. Printed in US A Part No, SP5909 FULL ONE YEAR WARRANTY ON L,RAFTSNIAN STATIONARY TOOL If this stationary tool fails due to a defect in material or workmanship within one year from the date of purchase, CONTACT THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES and Sears wilt repair it free of charge. This warranty applies only while this product is in the United If this Table Saw is used for commercial or rental purposes, from the date of purchase. This warranty gives you specific legal rights, and you may state to state. States. this warranty will apply for ninety days also have other rights which vary from Sears, Roebuck and Co°, D/817 WA Hoffman Estates, IL 60179 . .._ Safety Instructions For Table Saw Safety is a combination of common sense, staying alert and knowing how your table saw works,, Read this manual to understand this table saw Safety Signal Words DANGER: means if the safety information is not followed someone will be seriously injured or killed Before Using The Saw WARNING: to avoid mistakes that could cause serious, permanent injury, do not plug the table saw in until the following steps have been satisfactorily completed. * Completely assemble and align saw (See "Assembly" section) ° Learn the use and function of the ON-OFF switch blade guard, spreader, anti-kickback device, miter gauge, rip fence, table insert, blade elevation and m ® 1, Read manual before usingsaw. 2. Wear safety gogglesthat meet ANSI Z87.1Standards, E23417 ' 3. DOnotreacharoundorover saw blade. 12o VoIts 4. Keepblade guard downend In place for throughcuts. 3450 RP M 5. Do notdo freehand cuts. 1 t 5 Amp._ 6. Keep hands out of path of saw blade° 60 Hz_ I Ph I0" Blade 7. When ripping,use push stickwhen fence Is set 2 Inches or more from blade. When Installing Or Moving The Saw Avoid Dangerous Environment. • Use the saw in a dry, indoor place protected from rain, • Keep work area well lighted • Use recommended accessories Consult the owneCs manual Ior recommended accessories, The use of improper accessories may cause risk of injuryto persons To avoid injury from unexpected saw movement. . Bott or clamp the saw to firm level surface where there is plenty of room to handle and properly support the work- piece (See "Assembly-Mounting Your Saw" section) ° Support the saw so the table is level and the saw does not rock WARNING: means if the safety information is not foUowed someone could be seriously injured or killed, CAUTION: means if the safety information is not followed someone may be injured, blade tilt controls (See "Getting to Know Your Table Saw" section), . Review and understand all safety instructions and operating procedures in this manual. , Review the maintenance methods for this saw (See "Maintaining Your Table Saw" section)), -Find and read all the warning labels found on the saw (shown below), , WARNING 8,, Knowhow toreduce therisk of kickback, See Instructions for ripping, 9. When rlpNng, use push block and auxiliary fence wher fence Is set between1/2end2 Inchesfromblade. Do not make dp cutsnarrowerthan 1/2 ]nch_ l& Turn poweroffendwalt forbladeto stop before adjustingor servicing. o When using a table extension longer than t2" attached to any side of the saw, bolt the saw to a stationary sur_ face or prop up the outer end of the extension from the floor or bench top to keep the saw from tipping o Put the saw where neither operator nor bystanders must stand in line wilh the sawblade, ° To avoid injury from electrical shock, make sure your fingers do not touch the plug's metal prongs when plugging in or unplugging the saw, • Never Stand On Tool Serious injury could occur if the tool tips or you accidentally hit the cutting tool Do not store anything above or near the tool where anyone might stand on the tool to reach them, Before Each Use ° Replace damaged or missing parts before using the saw again, Inspect your saw, * Keep guards in place and in working order -To avoid injury from accidental starting, turn the switch . Use the sawblade guard, spreader and anti-kickback off, unplug the saw, and remove the switch key before pawls for any thru-sawing (whenever the blade comes raising or removing the guard, changing the cutting through the top of the workplace) Make sure the anti- tool. changing the setup, or adjusting anything Make kickback pawls work properly Make sure the spreader sure switch is in OFF position before plugging in, is in line with sawblade (See "Assembly-Aligning Blade • Check for alignment of moving parts, binding of moving Guard" section) parts, breakage of parts, saw stability, and any other ° Remove adjusting keys and wrenches Form a habit of conditions that may affect the...