Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
1t3.2473t0 BAND SAW WITH CABINET S_rial Number __ Model and serial numbers may be found at the left-hand side of the base. You should record both model and serial number in a safe place for future USe. im N CAUTION: READALL INSTRUCTIONS CAREFULLY 113.247310 113.24 7210 CRRFTSMRN 12-1NCH BAND SAW • assembly • operating • repair parts _,. j ..... _,' Sold by SEARS,ROEBUCKAND CO., Chicago, IL 60684 U.S.A. Part No. SP5086 Printed in U.S.A FULL ONE YEAR WARRANTY ON CRAFTSMAN BAND SAW If within one year from lhe date of purchase, this Craftsman Band Saw fails due to a defect in malarial or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES. This warranty applies only while this product is used in the United States. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., DEPT. 698/731A Sears Tower, Chicago, IL 60684 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS 1. KNOW YOUR POWER TOOL Read and understand the owner's manual and labels affixed to the tool. Learn its application and limitations as well as the specific potential hazards peculiar to this too!. 2. GROUND ALL TOOLS This tool is equipped with an approved 3-conductor cord and a 3-prong grounding type plug to fit the proper grounding type receptacle. The green conductor in the cord is the grounding wire. Never connect the green wire to a live terminal. 3. KEEP GUARDS IN PLACE, in working order, and in proper adjustment and alignment. 4. REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 5. KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents. Floor must not be slippery due to wax orsawdust. 6. AVOID DANGEROUS ENVIRONMENT Don't use power tools in damp orwet locations or expose them to rain. Keep work area well lighted. Provide adequate su rrou nding work space. 7. KEEP CHILDREN AWAY All visitors should be kept a safe distance from work area. 8. MAKE WORKSHOP CHILD-PROOF --with padlocks, master switches, orby removing starter keys. 9. DON'T FORCE TOOL It will do the job better and safer at the rate for which it was designed. 10. USE RIGHT TOOL Don't force tool or attachment to do a job it was not designed for. 11. WEAR PROPER APPAREL Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches) to get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. Roll long sleeves above the elbow. 12. USE SAFETY GOGGLES (Head Protection) Wear Safety goggles (must comply with ANSI Z87.1) at all times. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Also. use face or dust mask if cutting operation is dusty, and ear protectors (plugs or muffs) during extended periods of operation. 13. SECURE WORK Use clamps or a vise to hold work when practical. It's safer than using your hand, and frees both hands to operate tool. 14. DON'T OVERREACH Keep proper footing and balance at all times. 15. MAINTAIN TOOLS WITH CARE Keep _ools sharp and clean for best and safest performances. Follow instructions for lubricating an d changing accessories. 16. DISCONNECT TOOLS before servicing; when changing accessories such as blades, bits, cutters, etc. 17, AVOID ACCIDENTAL STARTING Make sure switch is in "OFF" position before plugging in. 18. USE RECOMMENDED ACCESSORIES Consult the owner's manual for recommended acce _. ories. Follow the instructions that accompalty the accessories. The use of improper accessories- may cause hazards. 19. NEVER STAND ON TOOL Serious inlu ry could occur if the tool is tipped or if the cutting tool is accidentally contacted. Do not store materials above or near the tool such that it is necessary to stand on the tool to reach them. 20. CHECK DAMAGED PARTS Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may effect its operation. A guard or other part that is damaged should be properly repaired or replaced. 21. NEVER LEAVE TOOL RUNNING UNATTENDED Turn power off. Don't leave tool until it comes to a complete stop. additional safety instructions for band saw Safety is a combination of common sense, staying alert, and knowing how your band saw works. BEFORE USING THE SAW: WARNING: TO AVOID MISTAKES THAT COULD RESULT IN SERIOUS, PERMANENT INJURY, DO NOT PLUG THE SAW IN UNTIL THE FOLLOWING STEPS HAVE BEEN SATISFACTORILY COMPLETED: 1. Assembly and alignment. 2. Learn the function and proper use of the on-off switch, bevel crank and lock, upper blade guide and lock knob, lower blade guide, tension adjusting knob and tension s...