Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Variable speed switch 2. Lock-on button 3. Saw blade locking lever 4. Saw blade support roller 5. Dust blower 6. Shoe plate 7. Dust extraction port 8. Saw blade storage compartment USE OF EXTENSION CORDS Make sure the extension cord is in good condition before using. Always use the proper size extension cords with the tool – that is, proper wire size for various lengths of cord and heavy enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in line voltage resulting in loss of power and overheating. For proper size cords see chart below. MOTOR Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply. SAVE THESE INSTRUCTIONS ASSEMBLY WARNING: Laceration Hazard. Before attempting any of the following operations, make sure that the tool is switched off and unplugged and that the saw blade has stopped. Used saw blades can be hot. Fitting the saw blade (figure A) - Hold the saw blade (9) as shown, with teeth facing forward. - Push the lever (3) downwards. - Insert the shank of the saw blade into the blade holder (10) as far as it will go. - Release the lever. Connecting a vacuum cleaner to the tool 1. Attach vacuum adapter (purchase separately) to back port. 2. Attach vacuum cleaner hose to vacuum adapter. USE WARNING: To reduce the risk of injury, never use the tool when the saw shoe is loose or removed. Adjusting the shoe plate for bevel cuts (figure B) The shoe plate can be set to make either a straight cut or a left or right bevel cut at an angle of 45°. Loosen the screws (11). - Pull the shoe plate (6) forward, rotate the shoe plate to the left or right and push it back into the 45° location. - Tighten the two screws (11). To reset the shoe plate for straight cuts: - Loosen the screws (11). - Pull the shoe plate (6) forward, rotate to the center and push it back into the 0° location. - Tighten the two screws (11). Switching On and Off - To switch the tool on, press the variable speed switch (1). The tool speed depends on how far you depress the switch. - For continuous operation, press the lock-on button (2) and release the variable speed switch. This option is available only at full speed. - To switch the tool off, release the variable speed switch. To switch the tool off, when in continuous operation, press the variable speed switch once more and release it. How to Use the Sightline® Feature (figure C) - Use a pencil to mark the cutting line. - Position the jigsaw over the line (12). Viewing from directly above the jigsaw the line of cut can be easily followed. B C E F Saw blade storage (figure D) Saw blades (9) can be stored in the storage compartment (14) located on the side of the tool. - Open the cover of the saw blade storage compartment (13) by holding the tab on the top of the door and pulling outwards. - Remove or store saw blades (9) in the storage compartment. NOTE: Blades are held in place by a magnet. To remove, press on either end of the blade to lift the opposite end. - Close the cover of the saw blade storage compartment (13) and make sure that it is latched closed. HINTS FOR OPTIMUM USE General - Use a high speed for wood, a medium speed for aluminum and PVC and a low speed for metals other then aluminum. Sawing laminates As the saw blade cuts on the upward stroke, splintering may occur on the surface closest to the shoe plate. - Use a fine-tooth saw blade. - Saw from the back surface of the workpiece. - To minimize splintering, clamp a piece of scrap wood or hardboard to both sides of the workpiece and saw through this sandwich. Sawing metal - Be aware that sawing metal takes much more time than sawing wood. - Use a saw blade suitable for sawing metal. - When cutting thin metal, clamp a piece of scrap wood to the back surface of the workpiece and cut through this sandwich. - Spread a film of oil along the intended line of cut. WARNING: Do not use a vacuum when cutting metal. Metal filings will be hot and may cause a fire. Rip Fence Ripping and circle cutting without a pencil line are easily done with a rip fence and circle guide (available at extra cost). Attaching Rip Fence (figure E & F) - Insert rip fence into slot on the right side of saw shoe as shown with cross bar facing down. - Place screw (14) into hole in bottom of shoe. - Align clamp bar (15) over screw with lipped edge facing down and pointing towards the rear of the saw. - Using a phillips screwdriver, run the screw into the threaded hole in the bar clamp. - Adjust to width of cut and tighten screw. Circle Cutting - Insert rip fence into slot on the right side of saw shoe ...