Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
3. The saw blade is set parallel to the miter gauge slot at the factory. The fence must be parallel to the miter gauge slot to do accurate work and to prevent kickback when ripping. To check the alignment: 4. Position the fence next to the miter gauge slot (Fig. 35). Clamp the fence to the table by pushing the locking lever (B) down . The edge of the fence should be parallel to the miter gauge slot. 5. If an adjustment is necessary, loosen the two screws (D) Fig. 35, and lift the locking lever (B). While holding the fence bracket (F) firmly toward the front of the saw, move the rear of the fence (A) until it is parallel with the miter gage slot. Tighten two screws (D) and push locking lever down (B). 6. Adjust the clamping action of the fence (A) Fig. 35 by lifting the locking lever (B) and turning the screw (E) clockwise to increase, or counterclockwise to decrease the clamping action of the fence. TABLE INSERT ADJUSTMENT DISCONNECT MACHINE FROM POWER SOURCE. 1. Make sure that the table insert (A) Fig. 36, is flush with, or slightly below, the surface of the table (B). 2. If the table insert is above the surface of the table, tighten the two table insert screws (C) Fig. 36 to lower the insert. Fig. 35 A D E F B C Fig. 36 A B C 17 MITER GAUGE OPERATION AND ADJUSTMENTS For cross-cutting (blade set 90 degrees to the table), the miter gauge can be used in either table slot. For bevel cross-cutting (with the blade tilted), use the miter gauge in the right table slot only so that the blade will be tilted away from the miter gauge and your hands. To operate the miter gauge, loosen the lock knob (E) Fig. 37, and rotate the miter gauge to the desired angle. E Fig. 37 ADJUSTING BLADE PARALLEL TO MITER GAUGE SLOTS The blade was adjusted parallel to the miter gauge slots at the factory. In order to ensure accurate cuts and help prevent kickback, check this adjustment. To adjust: DISCONNECT MACHINE FROM POWER SOURCE. 1. Raise the blade to its highest position and adjust the blade so that it is 90 degrees to the table. 2. Select a tooth on the saw blade that is set to the left. Mark this tooth with a pencil or marker. 3. Use a combination square (A) Fig. 38 against the miter gauge slot and adjust the blade (B) of the square until it touches the marked tooth. 4. Rotate the blade and check the same marked blade tooth at the rear of the saw table (Fig. 39). B A Fig. 38 Fig. 39 5. If the front and back measurements (Figs. 38 and 39) are not identical, you can adjust the blade. Start by loosening the nuts below the four screws (C) Fig. 40 on the table. Then loosen the screws (C). Carefully move the saw blade until the blade is parallel to the miter gauge slot. When done, tighten four nuts under the table and the four screws (C) Fig. 40 securely. NOTE: If sufficient adjustment cannot be achieved by loosening the screws (C) Fig. 40, loosen the screw (D) Fig. 40 necessary to make the adjustment. Fig. 40 18 CHANGING THE BLADE DISCONNECT THE MACHINE FROM THE POWER SOURCE. USE ONLY 10" DIAMETER SAW BLADES RATED FOR 4700 RPM OR HIGHER. USE ONLY SAW BLADES WITH 5/8" ARBOR HOLES. 1. NOTE: One 7/8" wrench is supplied with the saw for changing the saw blade. 2. Remove table insert (A) Fig. 41, and raise saw blade (F) to its maximum height. 3. To remove blade, place the wrench (D) on the flats of the arbor nut (C) to keep the arbor from turning. Place a piece of wood (B) flat on the table against the blade so that a tooth of the blade can “grab” the wood to keep the blade from turning. Use wrench to turn the arbor nut toward the front of the saw. Remove arbor nut, blade flange (E), and saw blade. 4. Assemble the new blade, making certain the teeth point down at the front of the saw table, and assemble outside blade flange and arbor nut. Using the piece of wood (B) to keep the blade from turning, tighten arbor nut by turning wrench (D) toward the rear of the saw. 5. Replace table insert. Fig. 41 F C ED B A MACHINE USE Common sawing operations include ripping and crosscutting plus a few other standard operations of a fundamental nature. As with all power machines, there is a certain amount of hazard involved with the operation and use of the machine. Using the machine with the respect and caution demanded as far as safety precautions are concerned, will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or completely ignored, personal injury to the operator can result. The following information describes the safe and proper method for performing the most common sawing operations. THE USE OF ATTACHMENTS AND ACCESSORIES NOT RECOMMENDED MAY RESULT IN THE RISK OF INJURY TO THE USER OR OTHERS. CROSS-CUTTING Cross-cutting requires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 42. The miter gage may be used in either table slot. When bevel cutting (blade tilted), use...