Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Grizzly, modell G0461

Hersteller: Grizzly
Dateigröße: 11.89 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Use the shims that came with the scoring blade set (Figure 38) to stack the scoring blade to the same thickness as the main blade. Figure 38. Typical scoring blade with shims. 5. Install the blade set with the teeth facing the opposite direction as the main blade, then reinstall the arbor flange and the arbor nut. 6. Place a hex wrench in the hole in the arbor and use the arbor wrench to tighten the arbor nut as shown in Figure 39. Note: The arbor nut has right-hand threads and tightens by turning clockwise. Figure 39. Installing the scoring blade. 7. Move the lower blade guard back into its original position and lock it in place. -27 G0460/G0461 12" Sliding Table Saw Aligning Blades The scoring blade must be aligned with the main blade to ensure satisfactory cutting results. To align the blades and riving knife: 1. DISCONNECT SAW FROM POWER! 2. Move the blade tilt to 0° (blade 90° to table), and raise the main blade all the way up. 3. Unlock the scoring blade adjustment using a hex wrench in the adjustment lock socket (Figure 40) and raise the blade to its highest point using a hex wrench in the vertical adjustment socket. 4.Remove the stop screw from the round rail and move the rip fence against the blade as shown in Figure 41. Horizontal Adjustment Vertical Adjustment Figure 40.Scoring blade adjustment controls. Adjustment Lock Figure 41. Fence against blade as a guide for aligning the scoring blade. -28 G0460/G0461 12" Sliding Table Saw 5. Use the adjustment controls to move the scoring blade so that the rip fence can touch both the scoring blade and the main blade. 6. Install the riving knife, making sure it is aligned with the blades. Crosscut Table Components and Hardware Needed: Qty Crosscut Table ...................................................1 Lock Plate...........................................................1 Adjustable Handles M10-1.5...............................1 Flat Washers 10mm ...........................................2 To install the crosscut table: 1. Thread the adjustable handles, with 10mm flat washers, two or three turns onto the studs in the lock plate, as shown in Figure 42. Note: The lock handles have a ratcheting action. Disengage them by pulling back on the handle. When held back (disengaged), the handles will rotate in either direction without turning the threads. When you let go of the handles, the internal spring will automatically engage them again. Figure 42.Adjustable handles threaded into lock plate to prepare for crosscut table installation. Crosscut Table Lock Plate Adjustable Handles 2. Slide the lock plate into the T-slot in the side of the sliding table. 3. With the help of an assistant, place the crosscut table on the pivot pin of the swing arm and over the studs of the lock plate (see Figure 43). T-Slot Pivot Pin Crosscut Table Leg Figure 43.Installing the crosscut table. 4.Lock the crosscut table in place with the adjustable handles. Crosscut Fence Components and Hardware Needed: Qty Crosscut Aluminium Fence ................................1 Long Knobs M10-1.5...........................................2 Flip Stops ...........................................................2 To install the crosscut fence: 1. Insert the T-bolts in the areas indicated in Figure 44, depending on whether or not you want the crosscut fence in the forward or rear position. (Refer to Page 36 for more details.) G0460/G0461 12" Sliding Table Saw Forward Mounting Points Rear Mounting Points Crosscut Fence Knobs Figure 44. Crosscut fence mounting. 2. Place a framing square along the edge of the sliding table and use the crosscut fence adjustment screw (Figure 45) to align the fence perpendicular to the sliding table. Note: Refer the instructions on Page 47 for additional details on making the fence perpendicular. Figure 45.Crosscut fence adjustment screw. -29 3. Thread the knobs onto the T-bolts to secure the crosscut fence. 4. Unlock the fence extension and slide the flip stops into the fence as shown in Figure 46. Figure 46. Stop block installation. Fence Scale Alignment Before operation, align the 0" mark on the rip fence scale with the right side of the blade to ensure accurate measurements. To align the rip fence scale with the blade: 1. Move the blade tilt to 0° (blade 90° to table), and raise the main blade all the way up. 2. Remove the stop screw from the round rail and move the rip fence against the blade. 3. Loosen the cap screws securing the scale. 4. Slide the fence scale to line up the first mark on the scale with the left edge of the rip fence and tighten the cap screws. 5. Slide the fence away from the blade and replace the stop screw. Dust Collection Components and Hardware Needed: Qty Blade Guard Dust Hood .....................................1 Flat Washer 8mm...............................................1 Adjustable Handle M8-1.25 x 28........................1 5" Dust Hose (not included) ...............................1 5" Hose Clamp (not included) ....................