Stimmen - 5, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Grizzly Dateigröße: 4.02 mb Dateiname: Unterrichtssprache:

2. Adjust the rip fence (Page 23). 3. Adjust the crosscut fence perpendicular to the blade (Page 48). Fence hits table top when sliding across table. 1. Front rail is too low. 2. Rip fence roller is too low. 1. Raise the rail (Page 23). 2. Adjust the roller (Page 23). Blade does not reach 90°, or blade does not reach 45°. 1. Blade stop nuts are out of adjustment. 1. Adjust the stop nuts (Page 47). The rip fence scale is not accurate. 1. The rip fence scale is out of calibration or was not set up correctly. 1. Adjust the rip fence scale (Page 31). Tilt or blade height handwheels difficult to turn. 1. Lock knob is tight. 2. Gears caked with dust. 1. Release the lock knob. 2. Clean out dust and grease the worm shafts. ▲warning 1 Disconnect power to the machine when performing any troubleshooting. Failure to do this may result in serious personal injury. G0588/G0591 12" Sliding Table Saws -51- SECTION 8: PARTS REF PART # iviair DESCRIPTION 1 P0588001 BODY 2 P0588002 TABLE 3 PW01M FLAT WASHER 8MM 4 PSB13M CAP SCREW M8-1.25 X 30 5 P0588005 SWITCH PLATE 6 P0588006 SWITCH BASE 7 PS06M PHLP HD SCR M5-.8 X 20 8 P0588008 MAG. SWITCH 220V-25A 9 PSB01M CAP SCREW M6-1 X 16 10 P0588010 COVER PLATE 11 P0588011 SCALE PLATE 12 PSB02M CAP SCREW M6-1 X 20 13 P0588013 ADJUSTMENT BOLT COVER 14 PSB26M CAP SCREW M6-1 X 12 15 P0588015 MOTOR COVER 16 PSB49M CAP SCREW M6-1 X 60 78 PB137M HEX BOLT M14-2 X 30 81 PN32M HEX NUT M14-2 199 P05910199 MAG. SWITCH 440V-14A Body REF PART # DESCRIPTION 199-1 P0591 01 99-1 OVERLOAD RELAY 199-2 P0591 01 99-2 MAGNETIC CONTACTOR 202 P0588202 DUST SHIELD 278 P0588278 SCALE DUST COVER 307 P0588307 TERMINAL BOX 308 P0588308 EMERGENCY BUTTON 309 PLABEL-12 READ MANUAL 2"W X 3 5/16" 310 P0588310 KICKBACK WARNING LABEL 311 P0588311 DISCONNECT POWER LABEL 312 PLABEL-11 SAFETY GLASSES 2" X 3 5/16" 313 PLABEL-29 CUTTERHEAD GUARD LABEL 314 P0588314 RAISING BLADE LABEL 315 P0588315 TILTING BLADE LABEL 316 P0588316 QUALIFIED PERSONNEL LABEL 317 PLABEL-34 PREWIRED 220V LABEL 318 P0588318 LOWER BLADE GUARD LABEL 319 PLABEL-14 ELECTRICITY LABEL 320 P0591320 G0591 ID LABEL 321 P0588320 G0588 ID LABEL -52- G0588/G0591 12" Sliding Table Saws G0588/G0591 12" Sliding Table Saws -53- Extension Tables REF PART # DESCRIPTION 3 PW01M FLAT WASHER 8MM 9 PSB02M CAP SCREW M6-1 X 20 17 P058801 7 TABLE INSERT 18 PFH07M FLAT HD SCR M5-.8 X 10 19 P0588019 EXTENSION WING (FRONT) 20 PSB13M CAP SCREW M8-1.25 X 30 21 PSS16M SET SCREW M8-1.25 X 10 23 P0588023 EXTENSION WING (RIGHT) 24 PB116M HEX BOLT M10-1.5 X 45 25 PW04M FLAT WASHER 10MM 26 P0588026 EXTENSION WING SUPPORT 27 PB138M HEX BOLT M16-2 X 100 28 PN13M HEX NUT M16-2 REF PART # DESCRIPTION 29 PN01M HEX NUT M6-1 30 PW03M FLAT WASHER 6MM 31 P0588031 SCALE BASE 32 P0588032 TUBE PLUG 33 P0588033 SCALE 36 P0588036 RACK 37 PSB03M CAP SCREW M5-.8 X 8 38 P0588038 RAIL 39 P0588039 STUD M12-1.75 X 120 40 PN09M HEX NUT M12-1.75 41 PW06M FLAT WASHER 12MM 279 P0588279 FENCE RAIL PLUG 45 X 33 -54- G0588/G0591 12" Sliding Table Saws G0588/G0591 12" Sliding Table Saws -55- Sliding Table REF PART # DESCRIPTION 9 PSB01M CAP SCREW M6-1 X 16 42 P0588042 SLIDING TABLE 43 P0588043 SLIDING TABLE END 44 PSB01M CAP SCREW M6-1 X 16 45 P0588045 RUBBER PLATE 46 PFH23M FLAT HD SCR M8-1.25 X 16 47 P0588047 GIB 48 PB83M HEX BOLT M6-1 X 16 49 P0588049 STEEL RAILS 50 P0588050 HANDLE 51 P0588051 HANDLE COVER 52 P0588052 STOP LEVER 53 P0588053 SLEEVE 54 P0588054 EXTENSION SPRING 55 PN13M HEX NUT M16-2 56 P0588056 STOP PIN 57 P0588057 HOLD DOWN BRACKET 58 PR02M EXT. RETAINING RING 14MM 59 PRP45M ROLL PIN 5 X 32 60 P0588060 COMPRESSION SPRING 61 P0588061 CAM 62 P0588062 HANDLE SHAFT 63 P0588063 BALL HANDLE REF PART # DESCRIPTION 64 P0588064 HOLD DOWN ARBOR 65 P0588065 PLASTIC HOLD DOWN WASHER 66 P0588066 T-NUT PLATE 67 P0588067 EDGE SHOE PLATE 68 P0588068 T-NUT PLATE 69 PB74M HEX BOLT M10-1.5 X 20 70 P0588070 ADJUST HANDLE M10-1.5 X 16 71 P0588071 STEEL BALL BASE 72 P0588072 STEEL BALL BASE SPONGE 73 P0588073 STEEL BALL DIA. 18MM 74 P0588074 STEEL BALL DIA. 11/16MM 75 P0588075 SLIDING BASE 76 P0588076 SLIDING BASE COVER (BACK) 77 P0588077 SLIDING BASE COVER (FRONT) 78 PB137M HEX BOLT M14-2 X 30 79 PB153M HEX BOLT M14-2 X 40 80 P0588080 ADJUSTMENT PLATE 81 PN32M HEX NUT M14-2 259 P0588259 HOLD DOWN PLATE 260 P0588260 KNOB M8-1.25 X 20 261 P0588261 HOLD DOWN SHAFT 302 PSB14M CAP SCREW M8-1.25 X 20 304 P0588304 PUSH HANDLE M14-2 X 16 -56- G0588/G0591 12" Sliding Table Saws G0588/G0591 12" Sliding Table Saws -57- Crosscut Table REF PART # DESCRIPTION 21 PSS16M SET SCREW M8-1.25 X 10 22 PN03M HEX NUT M8-1.25 25 PN02M HEX NUT M10-1.5 29 PN01M HEX NUT M6-1 37 PS05M PHLP HD SCR M5-.8 X 8 44 PSB01M CAP SCREW M6-1 X 16 82 P0588082 CROSSCUT TABLE 83 P0588083 CROSSCUT TABLE ROLLER 84 P0588084 SUPPORT ADJUSTMENT BLOCK 85 PSB04M CAP SCREW M6-1 X 10 86 PSS09M SET SCREW M8-1.25 X ...

Herunterladen

Geben Sie zwei Ziffern: