Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Set the change knob shown in Fig. 7 to “0” to eliminate the orbital operation (the blade moves only up and down). The orbital operation can be selected in 4 steps from “0” to “III”. Lever Fig. 3 Blade Blade holder Blade Blade holder Fig. 4 Blade Roller Blade Roller Fig. 5 Dial Fig. 6 English (2) For the hard material, such as a steel plate, etc., decrease the orbital operation. For the soft material, such as lumber, plastic, etc., increase the orbital operation to increase work efficiency. To cut the material accurately, decrease the orbital operation. 9. Cutting stainless steel plates This Jig Saw can cut stainless steel plates by using No. 97 blade. Carefully read “Concerning cutting of stainless steel plates” for proper operation. 10. Splinter guard (Sold separately) Using the splinter guard when cutting wood materials will reduce splintering of cut surfaces. Insert the splinter guard in the space on the base, and push it completely. (see Fig. 8) 11. Chip cover (Sold separately) Chip cover prevents chips from flying off and improves the efficiency of dust collector (Sold separately). Insert the chip cover between the base and lever, and push with a slight pressure until it catches in place. (Fig. 9) When removing chip cover, hold both sides of knob and slightly open until it can be removed from the Jig Saw. NOTE: There is a possibility that chip cover is frosted when cutting the metal. 12. Sub base (Sold separately) Using the sub base (made from steel) will reduce abrasion of aluminium base especially in cutting metals. Using the sub base (made from resin) will reduce scratching of cut surface. Attach the sub base to the bottom surface of base by attached 4 screws. 13. Lighting up the lamp CAUTION: Do not look in the light or see the source of light directly. To turn on the lamp, pull the trigger. Release the trigger to turn off. Change knob Fig. 7 Splinter guard Base Fig. 8 Lever Base Chip cover Fig. 9 13 English CUTTING CAUTIONS: In order to prevent blade dislodging, damage or excessive wear on the Plunger, please make sure to have surface of the base plate attached to the work piece while sawing. 1. Rectilinear cutting When cutting on a straight line, first draw a marking gauge line and advance the saw along that line. Using the guide (sold separately) will make it possible to cut accurately on a straight line. (1) Loosen the base bolt allen wrench attached on base. (Fig. 10) (2) Move the base fully forward (Fig. 11), and tighten the base bolt again. (3) Attach the guide by passing it through the attachment hole on the base and tighten the M5 bolt. (Fig. 12) (4) Set the orbital position to “0”. NOTE: To ensure accurate cutting when using the Guide (Fig. 10), always set the orbital position to “0”. 2. Sawing curved lines When sawing a small circular arc, reduce the feeding speed of the machine. If the machine is fed too fast, it could cause the blade to break. 3. Cutting a circle or a circular arc The guide also will be helpful for circular cutting. After attaching the guide by same way noted as above, drive the nail or screw into the material through the hole on the guide, then use it for a axis when cutting. (Fig. 13) NOTE: Circular cutting must be done with the blade approximately vertical to the bottom surface of the base. Fig. 13 Guide Nail screw Guide hole Fig. 10 Base Base bolt Allen wrench Fig. 11 Base Fig. 12 M5 bolt Guide Attachment hole English 4. Cutting metallic materials (1) Adjust the speed Dial between scales “3” and “4”. (2) Set the orbital position to “0” or “I”. (3) Always use an appropriate cutting fluid (spindle oil, soapy water, etc.). When a liquid cutting fluid is not avaiable, apply grease to the back surface of the material to be cut. 5. Pocket cutting (1) In lumber Aligning the blade direction with the grain of the wood, cut step by step until a window hole is cut in the center of the lumber. (Fig. 14) (2) In other materials When cutting a window hole in materials other than lumber, initially bore a hole with a drill or similar tool from which to start cutting. 6. Angular cutting The base can be swiveled to both sides by up to 45° for angular cutting. (Fig. 15) (1) Loosen the base bolt by allen wrench attached on base and move the base fully forward. (Fig. Base 10, 11) (2) Align the scale (from 0 degrees to 45 degrees by 15-degree increments) of the semi-circular part of the base with the [ ] mark on the gear cover. (Fig. 16) (3) Tighten the M5 bolt again. (Fig. 10) mark (4) Set the orbital position to “0”. NOTE: Angular cutting can not be done when adopting chip cover or dust collector. Semi-circular part Fig. 14 Scale Fig. 15 Fig. 16 CONCERNING CUTTING OF STAINLESS STEEL PLATES When used with the No. 97 blade, can cut stainless steel plates. Note the following to adjus the unit. CAUTION: . In order to prevent blade dislodging, damage or excessive wear on the Plunger, please make sure to have surface of the base plate attached to the work piece while sawing. English When cu...