Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
(Fig. 8, Fig. 9) (4) Pull the holder sleeve back slightly in the direction of the arrow mark shown in Fig. 10 (in the direction opposite to the arrow marked on the holder sleeve). When you do this, the spring force will return the holder sleeve to the correct position automatically. There is no need to fasten the holder sleeve at this time. (Fig. 10) (5) Pull the back of the saw blade two or three times by hand and check that the blade is securely mounted. When pulling the blade, you will know it is properly mounted if it clicks and the holder sleeve moves slightly. (Fig. 11) CAUTION: When pulling the saw blade, be absolutely sure to pull it from the back. Pulling other parts of the blade will result in an injury. 2. Dismounting the blade (1) Turn on and off the switching trigger several times so that the holder sleeve can jump out of the front cover completely. Thereafter, turn off the switch and remove the battery. (Fig. 6) Front Holder sleeve cover Fig. 6 Holder sleeve Fig. 7 Fig. 8 Blade Blade Plunger slit Plunger slit Fig. 9 English CAUTION: Be absolutely sure to keep the switch turned off and the battery removed to prevent any accident. (2) After you have turned the holder sleeve in the direction of the arrow mark shown in Fig. 7 and secured it, turn the blade so it faces downward. The blade should fall out by itself. If the blade does't fall out, pull it out by hand. CAUTION: Never touch the saw blade immediately after use. The metal is hot and can easily burn your skin. Blade Holder sleeve Fig. 10 Holder sleeve WHEN THE BLADE IS BROKEN Even when the saw blade is broken and remains inside the small slit of the plunger, it should fall out if you turn the holder sleeve in the direction of the arrow mark, secure the holder sleeve, and face the blade downward. If it doesn’t fall out itself, take it out using the procedures explained below. (1) If a part of the broken saw blade is sticking out of the small slit of the plunger, pull out the protruding part and take the blade out. (2) If the broken saw blade is hidden inside the small slit, hook the broken blade using a tip of another saw blade and take it out. (Fig. 12) MAINTENANCE AND INSPECTION OF SAW BLADE MOUNT Fig. 11 Machine Another blade Fig. 12 Holder (1) After use, blow away sawdust, earth, sand, moisture, etc., with air or brush them away with a brush, etc., to ensure that the blade mount can function smoothly. (2) Periodically lubricate the saw blade mount with machine oil through the semicircular slit at a state where the holder sleeve is turned in the direction of the arrow mark shown in Fig. 7. (Fig. 13) NOTE: If the saw blade mount is used without proper cleaning and lubrication, the rotation of the holder sleeve may be hampered by sawdust and particles of dust, disabling you to remove the saw blade Fig. 13 with your fingers. sleeve oil Semicircular slit In such a case, hold the periphery of the holder sleeve lightly using a pair of pliers and the like, and turn the holder sleeve to left and right little by little. After the saw blade has been successfully removed, be absolutely sure to clean it up with air, etc., carry out proper lubrication, and then check and see if the saw blade mount can function smoothly. English 19 3. Moving the base Loosen the set screw and move the base forward, as shown in Fig. 14. Tighten the set screw slightly, ensure the base does not move back and forth, and firmly tighten the set screw. Ensure that the base does not contact the blade. 4. Confirm that the battery is mounted correctly. HOW TO USE THE CORDLESS RECIPROCATING SAW CAUTION: Avoid carrying it plugged to the outlet with your finger on the switch. A sudden startup can result in an unexpected injury. Be careful not to let sawdust, earth, moisture, etc., enter the inside of the machine through the plunger section during operation. If sawdust and the like accumulate in the plunger section, always clean it before use. Do not remove the front cover (refer to Fig. 6). Be sure to hold the body from the top of the front cover. During use, press the base against the material while cutting. Vibration can damage the saw blade if the base is not pressed firmly against the workpiece. Furthermore, a tip of the saw blade can sometimes contact the inner wall of the pipe, damaging the saw blade. Select a saw blade of the most appropriate length. Ideally, the length protruding from the base of the saw blade after subtracting the stroke should be larger than the material (see Fig. 15 and Fig. 17). If you cut a large pipe, large block of wood, etc., that exceeds the cutting capacity of a blade; there is a risk that the blade may contact with the inner wall of the pipe, wood, etc., resulting in damage. (Fig. 16, Fig. 18) 1. Switch operation (1) Lock-off button The tool is equipped with a lock-off button. To acivate the trigger lock, move the button to the right positon. Move the button to the left to operate the tool. (Fig. 19, Fig. 20) Set screw 12 mm Hexagonal bar wr...