Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Bosch Dateigröße: 774.45 kb Dateiname: Unterrichtssprache:

BM 2610993482 2-04 2/9/04 9:17 AM Page 8 The following types of blades should only be 2. Blades with teeth that point straight out used with orbital Setting O: rather than up or down. 1. Blades with teeth that point downward 3. Carbide-tipped blades. (reverse-tooth blades). 4. Grit-edge blades. FOOTPLATE ANGLE ADJUSTMENT The footplate may be tilted to allow angle cuts up to 45° in either direction. To adjust footplate, loosen screw (A) with allen wrench, slide the footplate towards the front of the tool, and rotate to the desired angle, as marked on the angle scale. Detent slots will hold the footplate firmly at 0°, and there are additional position marks for 15° and 45° angles. FOOTPLATE PROTRACTOR (Not included) Intermediate angles may be set with a protractor. After positioning the footplate, securely tighten screw (A). On model 1584DVS, screw (A) is covered by sliding cover, which should be closed after making the footplate adjustment. Note that when the footplate is used on an angle, dust cover must be removed, and chip collection efficiency will be reduced. SCREW (A) FOOTPLATE INSERTS (1584AVS & 1584DVS) Model 1584AVS & 1584DVS will accept two footplate inserts which may be changed by removing the six screws (B). The steel insert is used for most general cutting operations, and the smooth plastic insert may be used to minimize scratches on fine surfaces. FOOTPLATE ANTI-SPLINTER INSERT To minimize splintering of the top surface of the material being cut, place the anti-splinter insert in the blade opening of the footplate. Note: This insert will only work with blades that have ground sides such as T301CD, T101B, T101D, and T101DP. -8- ANTI-SPLINTER INSERT SCREW (A) SCREW (B) (1584AVS & 1584DVS) COVER (1584DVS) DUST PORT (1584DVS) FOOTPLATE INSERT (1584AVS & 1584DVS) BM 2610993482 2-04 2/9/04 9:17 AM Page 9 FLUSH CUTTING To allow the saw to make a perpendicular cut close to a vertical surface, the footplate may be repositioned as follows. Remove screw (A), move footplate to the front mounting slot, and be sure the detent notch is aligned with the DUST EXTRACTION (1584AVS & 1584DVS) Model 1584DVS is equipped with a dust port for chip extraction. To use this feature, attach vacuum hose (optional accessory) to the dust port connector, than attach the dust port connector to the dust port. Connect the other end of hose to a shop vacuum cleaner with * COVER SCREW (A) detent slot in the footplate. Re-insert screw (A) into the threaded hole closest to the detent notch, and securely tighten. Note that when the footplate is retracted in this manner, only 90°cuts are possible, and dust cover or optional cutting guide may not be used. DETENT NOTCH 4530150 SCREW (A) ANGLE SCALE CHIP BLOWER Strongest blowing action for working inThe jigsaw is equipped with a three-position woods and similar materials. chip blower to help keep the cutting line clear of chips. By adjusting the chip blower lever, the force of the discharged air may be altered Medium blowing action. as follows; No blowing action adapter (optional accessories). For maximum efficiency, dust covermust be in place. Model 1584AVS can be converted to dustless by adding the "Dust Collection Adapter Kit" which is available from Bosch Service Centers or Distributors. * DUST PORT CONNECTOR 4530150 -9- * DUST PORT FOOTPLATE PLATE * COVER FOOTPLATE INSERT SCREW (B) * Included in "Dust Collection Adapter Kit" BM 2610993482 2-04 2/9/04 9:17 AM Page 10 Tool Tips Always be certain that smaller workpieces are securely fastened to a bench or other support. Larger panels may be held in place by clamps on a bench or sawhorses. To begin a cut, clearly mark the cutting line, and rest the front of the footplate on the work. Engage the switch, and move the blade into the work using only enough forward pressure to keep the blade cutting steadily. DO NOT FORCE, as this will not make the saw cut faster; let the blade do the work. When cutting metal, it is often advisable to use a lubricant to cool the blade and extend its life. Choose blades carefully, as the ability of the jigsaw to follow curves, provides smoother finishes, or faster cutting is directly related to the type of blade used. BLADE SELECTION • Choose blades carefully, as the ability of the jigsaw to make the fastest cuts, to follow tight curves, to achieve the smoothest finish and/or to maximize the life of the blade are directly related to the type of blade used. • Always use a blade that is appropriate for the cutting task. • Always make a test cut in a piece of scrap material. • Most jigsaw blades have upward-pointing teeth, which helps to pull the jigsaw against the workpiece and minimizes vibration. Blades with upward-pointing teeth produce a clean cut on the bottom of the workpiece. • Blades with downward-pointing teeth (reverse-tooth blade) can be used to produce a clean cut on the top of the workpiece (that side that faces the jigsaw's footplate), such as when cutting an already-installed countertop from the ...

Herunterladen

Geben Sie zwei Ziffern: