Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Black & Decker Dateigröße: 2.78 mb Dateiname: Unterrichtssprache:

No loose clothing or jewelry to get caught in moving parts, Rubber gloves and footwear are recommended when working outdoors, USE SAFETY GLASSES with most tools. Alsd face or dust mask if cutting operation is dusty. DON'T ABUSE CORD. Never carry tool by cord or yank if to disconnect from receptacle. Keep cord from heat, oil and sharp edges. 13. SECURE WORK. Use clamps or a vise to hold work. It's safer than using your hand and it frees both hands to operate tool. DON'T OVERREACH. Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. DISCONNECT TOOLS. When not in use, before servicing; when changing accessories such as blades, bits, cutters, etc. REMOVE ADJUSTING KEYS AND WRENCHES, Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. AVOID ACCIDENTAL STARTING. Don’t carry plugged-in tool with finger on switch. 2. 3. 4. 5. 6. 7, 8, 9, 10. 11, 12. 14. 15. 16. 17. 18. GUARANTEE Black & Decker guarantees, for one year from date of purchase, to correct by repair or parts replacement without charge any defect due to faulty material or workmanship. Simply return the complete unit, transportation prepaid, to any Black & Decker Service Center or Authorized Service Station. Naturally, we assume no responsibility for damage caused by misuse, careless handling or where repairs have been made or attempted by others. No other guarantee, written or verbal, is authorized by us. {«'ТмМЗкМс* Y«llowPages ftrStrvittftSat« SWITCH Full the trigger switch to turn the motor "ON”, Releasing the trigger instantly turns the motor “OFF,” but the blade will continue to rotate for a short time. For safer operation, this tool has no provision to lock the switch in the “ON” position. MOUNTING SAW BLADES 1. BE SURE" THE SAW IS DISCONNECTED FROM THE POWER SUPPLY! 2. To remove blade clamping screw: — a. ON NEW SAWS (without blade attached), turn screw counter-clockwise with blade wrench pro- } | vided. If screw does not loosen easily w from spindle, tap the outer end of the wrench sharply in a counter-clockwise direction with a piece of wood to "free” the screw ' ' threads. Remove screw and outer clamp washer. — b. ON SAWS WITH BLADE ATTACHED, turn the blade so that the single hole in the rim is exposed at the front of the saw. Put a nail through this hole and turn the blade counter-clockwise until the nail is against the housing and stops the blade from turning. Turn the blade clamping screw counter-clockwise with the blade wrench and remove the screw and outer clamp washer. 3. To attach the blade, retract the lower blade guard and slip the blade over the saw spindle against the inner clamp washer with printed side of blade out (teeth at bottom of blade pointing forward). Place outer clamp washer on spindle so that “flats” in washer fit “flats” on spindle. Thread on clamping screw to hold washer in position. Place a nail through hole in blade rim so that nail rests on front of saw shoe and keeps blade from turning. Tighten clamping screw (clockwise) firmly with the blade wrench. CUTTING DEPTH ADJUSTMENT DISCONNECT PLUG FROM POWER SUPPLY BEFORE MAKING THIS OR ANY OTHER ADJUSTMENT. Loosen wing nut on left side of sawdust ejector, raise or lower shoe to desired depth of cut. Allow blade tooth depth only to project below bottom of material. Tighten wing nut securely. BEVEL ANGLE ADJUSTMENT DISCONNECT PLUG FROM POWER SUPPLY BEFORE MAKING THIS OR ANY OTHER ADJUSTMENT. Loosen knob at front of saw and tilt saw base (shoe) to cutting angle desired. Retighten knob securely. SAW OPERATION Rest front of saw base (shoe) on work. Line up blade with cutting line. Blade teeth should not contact work. Lower blade guard should be free. Pull trigger and guide saw through its cut with firm pressure but without forcing. Undue force actually slows down the cutting and produces a rougher cut. Keep blades sharp. Dull or incorrectly set teeth may cause saw to swerve or stall under pressure. IF SAW STALLS, RELEASE THE TRIGGER, DISCONNECT PLUG FROM POWER SUPPLY AND THEN BACK THE SAW UNTIL IT IS LOOSE. BE SURE BLADE CLEARS THE WORK BEFORE RE-STARTING CUTTING. POCKET CUTS Adjust saw base (shoe) so blade cuts at desired depth. Tilt saw forward and rest front of base on material to be cut. Using lever, retract blade guard to an upward position. Lower rear of base until blade teeth almost touch cutting . line. Now release the blade guard and its contact with the work will keep it in position to open freely as you start the cut. Start the motor and gradually lower the saw until its base rests flat on the material to be cut. Advance / saw along cutting line until cut is f ^ ......_ ........ j completed. Release trigger and ——————............... ............' —.....-.............>..... allow blade to stop completely before wit...

Herunterladen

Geben Sie zwei Ziffern: