Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Makita Dateigröße: 1.08 mb Dateiname: Unterrichtssprache:

c-................................. amperes herts kilograms hours minutes seconds alternating current direct current no load speed alternating or direct current Class II Construction splash-proof construction watertight construction revolutions or reciprocation per minute number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50OFI or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3.Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. (11 Do not touch the terminals with any conductive material. (2)Avoid storing battery cartridge ina container with other metal objects such as nails, coins, etc. (3)Do not expose battery cartridge to water or rain. 6. Do not store the tool and Battery Cartridge in locations where the tempera- ture may reach or exceed 5OoC (122OF). 7. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. SAVE THESE INSTRUCTIONS. Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may acci- dentally fall out of the tool, causing injury to you or someone around you. Fig. 8 *Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly Charging *Your new battery cartridge is not charged. You will need to charge it before use. Use the high capacity battery charger Model DC1411 to charge the battery cartridge. *Plug the high capacity battery charger into the proper A.C. voltage source. The charg- ing light will flash in green color. *Insert the battery cartridge so that the plus and minus terminals on the battery car- tridge are on the same sides as their respective markings on the high capacity Battery cartridge Charg'ng'lght *If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the battery cartridge from the high capacity battery charger. *If the charging light flashes alternately in green and red color, a problem exists and charg ing is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged. Removing or installing the saw blade CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the hex wrench to loosen the bolt clock- wise. Then remove the bolt, outer flange and blade. :wrench To install the blade, follow the removal pro- cedure in reverse. BE SURE TO TIGHTEN THE BOLT SECURELY. I I Fig. 10 Saw blade Fig. 11 CAUTl ON : *Be sure the blade is installed with teeth pointing up at the front of the tool *Use only the Makita hex wrench to install or remove the blade. Hex wrench storage When not in use, the hex wrench can be conveniently stored. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before any adjustment is attempted. Adjusting depth of cut Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tightening the lever. CAUTION: I I Fig. 13 .Use a shallow depth of cut when cutting thin workpiece for cleaner, safer cuts. *After adjusting the depth of cut, always tighten the lever securely. Bevel cutting Loosen the screw on the bevel scale plate on the front of the base. Set for desired angle (0" -50") by tilting accordingly, then tighten the clamp screw securely. I 1 Bevel scale pla4 Screw CAUTION: After adjusting the depth of cut and bevel cutting angle, be sure to tighten the screw. Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0" engraved on it with your cutting line on the workpiece. For 45" bevel cuts, align the edge with 45" engrav...

Herunterladen

Geben Sie zwei Ziffern: