Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. 4 Selecting the cutting action Speed adjusting dial 002706 002712 1. Cutting action 1. Speed adjust- changing lever ing dial 1 1 This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action thrusts the blade forward on the cutting stroke and greatly increases cutting speed. To change the cutting action, just turn the cutting action changing lever to the desired cutting action position. Refer to the table to select the appropriate cutting action. 006376 Position Cutting action Applications 0 Straight line cutting action For cutting mild steel, stainless steel and plastics. For clean cuts in wood and plywood. Small orbit cutting action For cutting mild steel, aluminum and hard wood. Medium orbit cutting action For cutting wood and plywood. For fast cutting in aluminum and mild steel. Large orbit cutting action For fast cutting in wood and plywood. Switch action 002709 1 2 1. Lock-off button 2. Switch trigger CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To prevent the switch trigger from being accidentally pulled, a lock-off button is provided. To start the tool, push in the lock-off button and pull the switch trigger. Release the switch trigger to stop. The tool speed can be infinitely adjusted between 500 and 2,800 strokes per minute by turning the adjusting dial. Higher speed is obtained when the dial is turned in the direction of number 5; lower speed is obtained when it is turned in the direction of number 1. Refer to the table to select the proper speed for the work- piece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced. 006378 Workpiece to be cut Number on adjusting dial Wood 3 - 5 Mild steel 3 - 5 Stainless steel 3 - 4 Aluminum 2 - 3 Plastics 1 - 4 CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded and heated up. • The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing saw blade CAUTION: • Always clean out all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may cause insufficient tightening of the blade, resulting in a serious personal injury. • Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. • Always secure the blade firmly. Insufficient tightening of the blade may cause blade breakage or serious personal injury. 5 INSTALLATION 5. With the blade held against the blade holder, rotate the blade installing lever in the (5) direction until it release it. 1. Push the blade installing lever in the (1) direction to stops. 002722 002719 1 2 (5) 1. Blade installing lever 1. Blade installing lever 2. Blade (1) 1 2. Pull the blade installing lever in the (2) direction until it stops with a little click. If you have difficulty pulling it out, try to do so while moving it back and forth in the (3) direction. 3. Rotate the blade installing lever in the (4) direction until the clamp protrudes 5 - 7 mm from the blade holder. 002720 (2)(3) (4) CAUTION: • If you rotate the blade installing lever excessively, the clamp will also rotate and finally come off. In this case, re-install it properly as lately described in ’’Installing clamp’’. 4. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits properly into the groove of the roller. 002721 1 2 3 4 5 1. Blade holder 2. Clamp 3. Slot 4. Roller 5. Blade (6) 1 6. With the blade installing lever held in this position, push it in the (6) direction. Then rotate the blade installing lever to its original position. 002723 1. Blade installing lever Removal 1. Push the blade installing lever in the (1) direction to release it. 002719 1. Blade installing lever 2. Pull the blade installing lever in the (2) direction until it stops with a little click. If you have difficulty pulling it out, try to do so while moving it back and forth in the (3) direction. 3. Rotate the blade installing lever in the (4) direction and remove the blade. 002720 (2)(3) (4) 6 4. Rotate the blade installing lever in the (5) direction until it stops....