Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
7 Lock-on Button Ventilation Openings Allen Wrench Dust Collection Port Blade Orbit Selector Lever Blade Roller Guide Cutting Guide Slots Lock-on Button Ventilation Openings Allen Wrench Dust Collection Port Blade Orbit Selector Lever Blade Roller Guide Cutting Guide Slots English DESCRIPTION & SPECIFICATIONS FUNCTIONAL DESCRIPTION Power Source Single-Phase, 120V, AC 60Hz Amps 6 Watts 650 Speed 500-3000 Strokes/Minute Stroke Length 1 Inch Max Bevel Cut 45. Wood Cutting Capacity 2 3/8 Inches Steel Cutting Capacity 1/4 Inch Nonferrous Metal Cutting Capacity 3/4 Inch Weight 5.4 lbs Preset Speed Dial Trigger Switch Chip Guard Blade Plunger “Quick Fix” Blade Change System Base Plate Non Marring Base SPECIFICATIONS 8 English SYMBOLS Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Designation/Explanation V Volts Voltage (potential) A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power no No load speed Rotational speed, at no load .../min Revolutions or reciprocation per minute Revolutions, strokes, surface speed, orbits, etc. per minute Class II construction Designates double insulated construction tools Alternating current Type or a characteristic of current Safety Alert Precautions that involve your safety 9 English ASSEMBLY & OPERATION PRIOR TO OPERATION 1. Check Power Supply Ensure that the power source to be utilized conforms to the power source requirements specified on the tool nameplate. Ensure the receptacle being used accepts the plug tightly. If a faulty receptacle is used, it may cause overheating, resulting in a serious hazard. 2. Check Work Area Confirm that the work site is placed under appropriate conditions conforming to precautions prescribed in the safety section of this manual. 3. Before Plugging in the Tool Ensure that the power tool switch is in the OFF position to prevent the tool from accidental start up which could cause serious injury. 4. Blade Installation a) Unplug tool b) Slide the chip guard up to allow access to the Quick Fix knob. – Fig 1 c) Turn the “Quick Fix” knob until it stops. – Fig 2 d) Insert the blade up to the stop and make sure the smooth side of the blade is resting against the blade roller guide. – Fig 2 e) Release the “Quick Fix” knob. - Fig. 3 f) Check that the blade is securely fixed by pulling downward. g) Slide the chip guard down until it stops. – Fig 4 Fig. 1 Fig. 2 5. Adjusting the Blade Speed a) Variable Speed Trigger Switch This tool is equipped with a variable speed trigger switch. The tool can be turned on or off by squeezing or releasing the trigger. The speed can be adjusted from the minimum to the maximum speed selected on the preset adjusting dial by the pressure you put on the trigger. 10 English Fig. 3 Fig. 4 More pressure on the trigger results in faster blade speed. Less pressure on the trigger results in slower blade speed. b) Preset Speed Adjusting Dial This feature allows you to preset the maximum speed by rotating the dial on the top handle of the saw to a higher or lower setting. The tool will never operate at a speed higher than the maximum speed setting selected on the speed dial. – See Fig 5 c) Electronic Cruise Control This tool is equipped with an electronic module with tachometric feedback which guarantees constant blade speed under load. This feature allows the saw to cut at a consistent rate of speed and maintain a consistent finish quality even if the load on the tool increases or decreases. Fig. 5 d) Lock-On Button This button is located on the side of the saw’s handle above the trigger and allows you to continuously operate the saw, at the speed set with the preset Speed Dial, without holding the trigger. To lock the trigger “ON”, squeeze the trigger, depress the button, and then release the trigger – Fig. 6. To unlock the trigger, squeeze the trigger and release it without depressing the lock-on button – Fig. 7 11 English Fig. 6 Fig. 7 Important: Be sure that the switch and Lock-On button are not engaged before plugging in tool. 6. Adjusting the Orbital Action a) This tool is equipped with orbital action, which moves the blade from front to back as well as up and down. This feature allows you to maximize the cutting efficiency in the material being cut – Fig 8 & 9. Fig. 8 Fig. 9 b) Use the following chart to help determine the appropriate orbital setting for your application. This chart is intended as a guideline only and test cuts in scrap material should be made first to determine the appropriate setting. 12 English Setting 0 Good for metals, plastics, and best quality finish in wood and wood products such as plywood, chip board, etc. Also good for scroll work. Setting 1 Better quality cut in wood and wood products where speed of cut is more imortant than quality of cut. Setting 2 Good quality with faster cut speed in wood and wood products. Setting 3 Fastest spee...
Dieses Handbuch ist für folgende Modelle:Kreissägen - FJ85 (849.04 kb)