Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
3. Slide the Battery (H) forward until it firmly seats into the Charger Base (O). The GREEN light will go on and begin to flash. This indicates the battery is charging. 4. The charging period takes approximately one hour for a fully discharged battery and less for a battery not fully discharged. When the Battery (H) has been fully charged the Charger Base (O) will beep once and the GREEN light will stay on steadily. 5. Remove the Battery (H) from the Charger Base (O) and insert the Battery (H) into the base of the tool. 6. Press the test button on the Battery (H) to verify the battery is fully charged. 7. All four lights lit represent a full charge of the Battery. INSTALLING & REMOVING THE BATTERY PACK Warning! Do not touch the Trigger Switch (B) or the Trigger Release Button (A) while installing the Battery. Insert the Battery (H) into the saw body as shown in Fig. 1. Fig. 2 shows the Battery (H) correctly inserted in the Charger Base (O). FIGURE 1 FIGURE 2 Charger Base SKU 93808 For technical questions, please call 1-800-444-3353. Page 10 English NOTE: When removing the Battery Pack from the saw body, press in on the two locking tabs located on each side of the Battery Pack and pull straight out from the body. Warning! If two or more batteries are to be charged, allow the Charging Base time to cool down between charges. WORK LIGHT AND LASER GUIDE Your 18 Volt Cordless Circular Saw has an integrated Work Light and a Laser Guide. The Work Light (F) is activated and deactivated by depressing the Work Lamp Switch (C) located on the top of the saw. The Laser Guide (E) is activated by pulling the trigger and can be activated no other way. NOTE: The Work Light and Laser Guide are aids and are not intended to function in any manner other than that described in this manual. SKU 93808 For technical questions, please call 1-800-444-3353. Page 11 English OPERATION Install the Saw Blade. Prepare and secure the material to be cut before turning on saw. The Battery (H) should have a full charge before using saw. Remove battery before making any adjustments. Refer to Figure 3, on page 18. INSTALLING CUTTING BLADE NOTE: The Lock Bolt is a reverse thread. 1. Remove The Battery (O) before making any adjustments. 2. Press on the Spindle Lock Button (J) to keep the Saw Blade from moving while turning the Blade Bolt (I). 3. Using the Hex Key (P), loosen and remove Lock Bolt (I) and Outer Flange (I). 4. Rotate the Lower Blade Guard (K), counterclockwise to allow entry of the Saw Blade. 5. Insert Saw Blade through the Base Plate (M) until blade fits on the motor spindle. Notice the arrow on the Lower Blade Guard (K) and the arrow on the Saw Blade. They should be pointing in the same direction. 6. Replace the Outer Flange (I) and Blade Bolt (I). Tighten with the Hex Key (P) while pressing on the Spindle Lock Button (J). Verify that the Spindle Lock Button (J) is in the up (unlocked) position. 7. Replace the Hex Key (P) to its storage hole in the housing of the saw. ADJUSTING THE SAW PRIOR TO CUTTING 1. To adjust the angle of blade, loosen the Bevel Cut Adjustment Knob (G) and move Base Plate (M) while observing the degree scale located next to the Bevel Cut Adjustment Knob (G). 2. To adjust the depth of the cut, loosen the Depth Adjustment Knob (N), which is located next to the motor housing, and move the Base Plate (M) while observing the amount of Saw Blade exposed under Base Plate. Tighten the Depth Adjustment Knob (N) after making the adjustment. 3. Rip Fence installation and adjustment: The Rip Fence can be inserted into either the left or right side at the toe of the Base Plate (M). Insert the Rip Fence into the fence guides until it contacts the Retention Bolt (Q). Loosen the Retention Bolt (Q) until the fence can slide through then secure it by turning the Retention Bolt (Q) clockwise. The Rip Fence is adjustable from 0”- 5”. ( Refer to Page 18, Fig. 3) SKU 93808 For technical questions, please call 1-800-444-3353. Page 12 English FUNCTIONS The 18 Volt Cordless Circular Saw has the following features, as shown in Fig. 3 below. (K) Lower Blade Guard (L) Light Holder (M) Base Plate (N) Depth Adjustment Knob (next to the motor of the saw not shown) (O) Charger Base (shown on page 16) (P) Hex Key (Inserted in Saw Body next to motor) (Q) Retention Bolt (R) Dust Port (A) Trigger Release Button (B) Trigger Switch (C) Work Lamp Switch (D) Off hand handle (E) Laser Guide (F) Work Light (G) Bevel Cut Adjustment Knob (H) 18 volt NiMh Battery (I) Blade Flange and bolt (J) Spindle Lock for blade change (between saw body and upper blade guard) A H C B F I G Figure 3 J E K L N D Q P R SKU 93808 For technical questions, please call 1-800-444-3353. Page 13 English PREPARE MATERIAL BEFORE CUTTING 1. Support large panels to minimize risk of blade pinching and saw kickback. 2. Use a rip fence or secured straight edge guide when ripping material. 3. Securely clamp material to be cut to work bench. 4. Make sure saw does not cut into supports o...