Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
11. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. 12. MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry, and keep cutoff grinding wheels clean and sharp for better and safer performance. 13. MAINTENANCE: For your safety, service and maintenance should be performed regularly by a qualified technician. 14. USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain applications for which this product was designed. Do not use small equipment, tools or attachments to do the work of larger industrial equipment, tools or attachments. Do not use this product for a purpose for which it was not intended. SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS 1. DANGER! Do not use unapproved accessories. Do not use circular saw blades or wire brushes on this tool. Do not use any accessory except 6” Cut-Off Grinding Wheels rated at 9,000 RPMs or higher. 2. GUARD AGAINST ELECTRIC SHOCK. Do not submerge the Cut-Off Saw in water or other liquids. Always prevent body contact with grounded surfaces such as pipes, radiators, ranges, refrigerators, etcetera. Do not operate the Cut-Off Saw if the operator is standing in water. SKU 41453 For technical questions, please call 1-800-444-3353. PAGE 3 To comply with the National Electric Code (NFPA70), and to provide additional protection from the risk of electrical shock, the Cut-Off Saw should only be connected to a To comply with the National Electric Code (NFPA70), and to provide additional protection from the risk of electrical shock, the Cut-Off Saw should only be connected to a 3. ALWAYS USE A 3 PRONG PLUG ADAPTER (not provided). This Cut-Off Saw is equipped with a 2 prongPower Cord Plug (31). For increase safety always attach and use a 3 prong, grounded, Plug Adapter. (See Figure A, and Assy. Diagram.) FIGURE A 3 PRONG PLUG ADAPTER 2 PRONG PLUG (31) 115 VOLT OUTLET 4. MAKE SURE THE POWER SWITCH IS IN THE “OFF” POSITION BEFORE PLUGGING IN THE POWER CORD. 5. DO NOT ABUSE THE POWER CORD. Do not use the Power Cord to pull the Plug from a power outlet. Keep Power Cord away from heat, oil, sharp edges, and moving parts. Replace a damaged Power Cord immediately. Route the Power Cord safely. Protect it from being damaged by other equipment in the work area. Do not route the Power Cord where it can be walked on or tripped over. 6. IF YOU USE AN EXTENSION CORD, MAKE SURE TO USE ONLY UL APPROVED CORDS HAVING THE CORRECT GAUGE AND LENGTH. (SEE FIGURE B.) REQUIRED EXTENSION CORD GAUGE Nameplate Amperes Extension Cord Length 25’ 50’ 75’ 100’ 150’ 200’ 0 - 5 16 16 16 14 12 12 5.1 - 8 16 16 14 12 10 - 8.1 - 12 14 14 12 10 -- 12.1 - 15 12 12 10 10 -- 15.1 - 20 10 10 10 --- FIGURE B SKU 41453 For technical questions, please call 1-800-444-3353. PAGE 4 7. NOTE: Performance of this tool may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. 8. MAINTAIN A SAFE WORK ENVIRONMENT. Do not use the Cut-Off Saw in or near damp or wet areas. Do not expose this tool to rain. Keep the work area well lit. Make sure there is adequate surrounding workspace. Use this tool in a well ventilated area. Do not operate this tool in the presence of flammable liquids, gases, or dust. 9. DO NOT FORCE THE EQUIPMENT. This Cut-Off Saw will do the work better and safer at the speed and capacity for which it was designed. 10. KEEP ALL GUARDS IN PLACE AND IN WORKING ORDER. 11. REMOVE ALL ADJUSTING WRENCHES FROM THE CUTOFF SAW BEFORE TURNING IT ON. 12. AVOID UNINTENTIONAL STARTING. Make sure you are prepared to begin work before turning the Power Switch “ON.” 13. ALLOW THE CUTOFF GRINDING WHEEL TO SPIN UP TO FULL SPEED BEFORE FEEDING MATERIAL INTO IT. When turning it off, allow the Cut-Off Grinding Wheel to spin down and stop on its own. Do not press against the Cut-Off Grinding Wheel to stop it. 14. ALWAYS KEEP HANDS AND FINGERS AWAY FROM THE CUTOFF GRINDING WHEEL. Never pass hands directly in front of, to the rear, or below the Cut-Off Grinding Wheel when cutting a workpiece. 15. DO NOT FORCE THE CUTOFF GRINDING WHEEL INTO THE WORKPIECE WHEN CUTTING. Apply moderate pressure, allowing the Cut-Off Grinding Wheel to cut without being forced. 16. NEVER ATTEMPT TO REMOVE MATERIAL STUCK IN THE MOVING PARTS OF THE CUTOFF SAW WHILE IT IS PLUGGED IN AND RUNNING. 17. TURN OFF THE CUTOFF SAW IF THE WORKPIECE IS TO BE BACKED OUT OF AN UNCOMPLETED CUT. 18. MAKE SURE THE WORKPIECE IS FREE FROM ANY FOREIGN OBJECTS WHICH COULD DAMAGE THE CUTOFF GRINDING WHEEL. 19. MAKE SURE THE WORKPIECE IS SUPPORTED AT ALL TIMES DURING OPERATION. Use a Roller Stand (not provided) with a larger workpiece if necessary. SKU 41453 For technical questions, please call 1-800-444-3353. PAGE 5 20. MAINTAIN CONTROL OF THE WORKPIECE AT ALL TIMES. Whenever possible, secure the work piece with clamps, in a vise, etcetera. 21. ALWAYS DISCONNECT THE CUTOF...