Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: DeWalt Dateigröße: 19.76 mb Dateiname: Unterrichtssprache:

If an adapter is used to accommodate a two-prong receptacle, the adapter wire must be attached to a known .pound. Never remove the third prong. 4. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to ж that keys and adjusting wrenches are removed before turning on tool. 5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 6. AVOID DANGEROUS ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp or wet locations. Keep your work area well Illuminated. 7. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area. 8. MAKE WORKSHOP KIDPROOF—with padlocks, master switches, or by removing starter keys. 9. DON’T FORCE TOOL. It will do the job better and be safer at the rate for which It’ was designed. 10. USE -RIGHT TOOL Don*! force tooi or attachment to do a job it was not designed tor. 11. ■ WEAR PROPER APPAREL No loose clothing or jewelry to get caught in moving parts. Rubber-soled footwear is recommended for best footing, 12. USE PROTECTIVE GLASSES. Also use face or dust mask if cutting .operation is dusty. 13. NEV01 'STAND ON.*TOOLSerious:-injury could :0ccur-if the tool is tipped or if the cutting tool is accidently contacted. 14. DON’T OVERREACH. Keep your proper footing and balance.....at all.....times. 15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best performance. Follow instructions for lubricating and changing accessories. li. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits, cutters. 17. USE RECOMMENDED ACCESSORIES. Consult owner's manual. Use of improper accessories may be hazardous. 18. AVOID ACCIDENTAL STARTING. Make sure switch is off before plugging in cord. 19. KEEP HANDS AWAY FROM CUTTING AREA. 20. DO NOT OPERATE electric tools in gaseous or explosive atmospheres. Motors in these tools normally soark, and the sparks might ignite fumes. 21. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to assure that it will operate properly and perform its intended'function—check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its 'operation, A guard or other part that is damaged should be properly repaired or replaced. MAINTENANCE & OPERATION 1. Be sure blade rotates clockwise when facing arbor. 2. Secure table frame to a bench table, leg stand, etc. before operating saw. It is recommended that whatever saw support is used should slope to the rear sufficiently to prevent the blade unit from creeping forward due to gravity and it should be securely anchored to the floor to prevent undesired movement. 3. Be sure all clamp handles are tight before starting any operation. Push back to tighten. Pull to loosen. 4. Make sure blade and arbor collar are clean and collar is against blade. Tighten arbor screw securely, and set clutch. (See clutch instructions). . 5. Keep the saw blade sharp and properly set. 6. Use anti-kickback device on guard; never remove it. 7. Keep arm tracks and bearing surfaces clean and dry. Periodically lubricate balls with a dry lubricant. 8. Periodically recheck alignment (see alignment chart). 9. Keep motor air slots clean and free of chips. 10. Do not attempt to operate saw on anything but the designated voltage. 11. Do not use blades of larger diameter than 8". 12. Keep the saw blade sharp. Cracked or improper type blades should not be used. 13. Never oil or grease arm tracks or the motor. 14. Do not wedge anything against fan to hold motor shaft. . 15. Saw and table top should be kept away from dampness. 16. Never force cutting action. Stalling or partial stalling of the motor is dangerous and can cause major damage to motor winding. If motor stalls turn switch off immediately. 17. Do not remove ground prong from plug. Never operate the saw unless it is properly grounded. 18. Be sure you are alert. If you are fatigued, rest before you work. 19. Always use blade guard properly adjusted for the operation you are performing. CAUTION: Do not clean the lower plastic guard with solvents or soaps. Use ONLY a cloth dampened with water. 20. The motor and yoke should be safely behind the should always be returned to the rear of the table after making a cut, and before you remove any stock from the table. 21. Be certain the equipment is turned off before making any adjustments. 22. When ripping, always feed the material past the blade guard from the side opposite the anti-kickback device. Never stand in back, or in direct line with the saw blade. Never rip from the wrong end. 23. The saw blade or tool should be completely stopped, and switch key removed, before you leave the machine. 24. Always turn switch off before removing key. 7 INSTRUCTIONS GROUNDING This tool should be grounded while in use to protect the operator from electric shock. 1. Cord-Connected Tools—The tool ...

Herunterladen

Geben Sie zwei Ziffern: