Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Loosen the screws on the underside of the miter table attachment (approx. 1/2 turn). Also loosen the preset angle release button and locking screw if necessary. Align the saw blade of the mounted saw with the aid of a protractor or square to achieve the 0. setting. Tighten the thumbscrew to secure setting, then securely tighten the screws on the underside of the table attachment (Fig. 11). ALIGNING SAW BLADE 90. TO THE MITER TABLE ATTACHMENT If necessary, the blade can be re-aligned to be 90. to the table. First, loosen the thumbscrew. Then align the saw blade of the mounted saw with the aid of a square. Rotate the blade alignment screw clockwise or counterclockwise until you achieve the 90 degree setting. Then tighten the thumbscrew (Fig. 12). DUST EXTRACTION The miter table attachment is equipped with a dust port for dust extraction. To use this feature, attach a vacuum hose (optional accessory) to the dust port, and then attach opposite end to a shop vacuum cleaner (Fig. 13). -10- FIG. 11 FIG. 13 ANGLE INDICATOR ADJUSTMENT SCREWS LOCKING SCREW BLADE ALIGNMENT SCREW FIG. 12 DUST PORT Operating Instructions for Saw ! WARNING Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. When working, never hold tool with your hand or fingers in area of the saw blade. The fingers of the guiding hand must always be kept behind the limiting ridge (Fig. 14). FIG. 14 LIMITING RIDGE SLIDE "ON-OFF" SWITCH The tool is switched "ON" by the slide switch located at the side of the motor housing. The switch can be locked in the "ON" position, a convenience for long cutting operations. TO LOCK THE SWITCH "ON", slide the switch button forward and press "IN" the FRONT portion. TO UNLOCK THE SWITCH, simply press and release the REAR portion of the button. The switch is spring loaded and will snap back automatically. VARIABLE SPEED DIAL Your tool is equipped with a variable speed dial. The blade stroke rate may be adjusted during cutting operation by setting the dial on or between any one of the six numbers. Application Position Softwood 3 - 6 Hardwood 4 - 6 Plastic 1 - 6 The optimum stroke rate depends on the material and must be determined by testing on similar materials in each application. POSITIONING THE BLADE AGAINST THE WORK Never saw with the blade facing upward or in the direction of the body (Fig. 15). FIG. 15 The cutting action of this saw is similar to a handsaw. Place the blade on the edge of the work- piece. The blade should be held at a steep angle to the workpiece approx. 60° (Fig. 16A.) It is difficult to begin cutting on the flat of a workpiece (Fig.16B). FIG. 16 AB Pull blade thru the workpiece maintaining a steep angle when cutting (Fig. 17A). Do not start cutting on the back edge and allow tip to plunge into workpiece (Fig. 17B) FIG. 17 A B -11 When sawing profile strips, start sawing on the edge, not on a radius (Fig. 18). To ensure an exact starting position for a cut, clamp a of wood piece along the cutting line, and cut along the edge (Fig. 19). FIG. 18 FIG. 19 FREE-HAND SAWING After blade is positioned properly,turn the tool on and move into the workpiece. Use only enough pressure to keep the blade cutting steadily. Do not force, as this will not make the saw cut any faster; let the blade do the work. Make sure that the saw blade tip goes into free space on the other side of the material. The cutting path must be free of obstacles both above and below the workpiece. To prevent splintering, avoid pressure on the blade at the end of the cut. When the cut is complete, turn off the tool immediately. Do not bring the saw blade to a stop by applying side pressure after turning the tool off. Always let the tool come to a complete stop before putting it down. Operating Instructions for Saw with Miter Table Attachment ! WARNING Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. ! WARNING When using the tool in the miter table attachment, the blade must never be used with the teeth pointing up. Contact with the blade while in use will cause an injury. ! WARNING Do not trap blade tip while cutting. If the blade tip strikes an obstruction it will kick-back ,or blade will buckle. The use of the miter table attachment included with the model 1640VSK kit allows the tool to be used in a stationary position (See figure. 2) Keep hands away from the immediate cutting area. The saw should not be used with any other miter table attachment or miterbox. Cuts of 0. as well as miter cuts of any angle can be made on your workpiece with the miter table attachment. Clamp the saw blade with the teeth pointing downward, and the teeth protector in place before operating the tool. When using the saw with the miter table attachment, the general purpose saw blade must b...
Dieses Handbuch ist für folgende Modelle:Kreissägen - 1640VSK (2.57 mb)