Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
4. Slide blade through slot in the foot and mount it against the INNER WASHER on the shaft. Be sure the large diameter of the INNER and OUTER washers lay flush against the blade. 5. Reinstall OUTER WASHER. First tighten BLADE STUD finger tight, then TIGHTEN BLADE STUD 1/8 TURN (45°) WITH THE WRENCH PROVIDED. Do not use wrenches with longer handles, since it may lead to over tightening of the blade stud. VARI-TORQUE CLUTCH This clutching action is provided by the friction of the OUTER WASHER against the BLADE and permits the blade shaft to turn when the blade encounters excessive resistance. When the BLADE STUD is properly tightened (as described in No. 5 of Attaching The Blade), the blade will slip when it encounters excessive resistance, thus reducing saw’s tendency to KICKBACK. One setting may not be sufficient for cutting all materials. If excessive blade slippage occurs, tighten the blade stud a fraction of a turn more (less than 1/8 turn). OVERTIGHTENING THE BLADE STUD NULLIFIES THE EFFECTIVENESS OF THE CLUTCH. FIG. 2 LOCK BUTTON ONE TOOTH LENGTH SHOULD PENETRATE WOOD FOR MINIMUM SPLINTERING ONE TOOTH LENGTH SHOULD PENETRATE WOOD FOR MINIMUM SPLINTERING BM 2610968995 6/00 7/14/00 8:25 AM Page 9 Operating Instructions DEPTH ADJUSTMENT the handle. Tighten lever at the depth setting Disconnect plug from power source. Loosen desired. Check desired depth (Fig. 3). the depth adjustment lever located between Not more than one tooth length of the blade the guard and handle of saw. Hold the foot should extend below the material to be cut, for down with one hand and raise or lower saw by minimum splintering (Fig. 4). FIG. 4 Inches Inner Scale Calibrated In CALIBRATED DEPTH BRACKET Outer Scale Calibrated For Standard Lumber Sizes DEPTH ADJUSTMENT LEVERFIG. 3 QUADRANT BEVEL ADJUSTMENT LEVER LINE GUIDE For a straight 90° cut, use right side of notch in the foot. For 45° bevel cuts, use the left side (Fig. 8). The cutting guide notch will give an approximate line of cut. Make sample cuts in scrap lumber to verify actual line of cut. This will be helpful because of the number of different blade types and thicknesses available. To ensure minimum splintering on the good side of the material to be cut, face the good side down. -9 45° BEVEL CUTS 90° VERTICAL CUTS FIG. 8 90° CUTTING ANGLE CHECK Disconnect plug from power source. Set foot to maximum depth of cut setting. Loosen bevel adjustment lever, set to 0° on quadrant, retighten lever and check for 90° angle between the blade and bottom plane of foot with a square (Fig. 5). Make adjustments by turning the small alignment screw, if necessary (Fig. 6). FIG. 5 FIG. 6BEVEL ADJUSTMENT LEVER BLADE 90° FOOT ALIGNMENT SCREW BEVEL ADJUSTMENT Disconnect plug from power source. The foot can be adjusted up to 45° by loosening the bevel adjustment lever at the front of the saw. Align to desired angle on calibrated quadrant. Then tighten bevel adjustment lever (Fig. 7). Because of the increased amount of blade engagement in the work and decreased stability of the foot, blade binding may occur. Keep the saw steady and the foot firmly on the workpiece. FIG. 7 BM 2610968995 6/00 7/14/00 8:25 AM Page 10 SWITCH When starting the tool, hold it with both hands. ! WARNING The torque from the motor can cause the tool to twist. To turn tool “ON”, squeeze the trigger switch. To turn the tool “OFF”, release the trigger switch, which is spring loaded and will return to the off position automatically. Your saw should be running at full speed BEFORE starting the cut, and turned off only AFTER completing the cut. To increase switch life, do not turn switch on and off while cutting. GENERAL CUTS Always hold the saw handle with one hand and the auxiliary handle or housing with the other. ! WARNING Always be sure either hand does not interfere with the free movement of the lower guard. Maintain a firm grip and operate the switch with a decisive action. Never force the saw. Use light and continuous pressure. ! WARNING After completing a cut and the trigger has been released, be aware of the necessary time it takes for the blade to come to a complete stop during coast down. Do not allow the saw to brush against your leg or side, since the lower guard is retractable, it could catch on your clothing and expose the blade. Be aware of the necessary blade exposures that exist in both the upper and lower guard areas. When cutting is interrupted, to resume cutting: squeeze the trigger and allow the blade to reach full speed, re-enter the cut slowly and resume cutting. When cutting across the grain, the fibers of the wood have a tendency to tear and lift. Advancing the saw slowly minimizes this effect. For a finished cut, a cross cut blade or miter blade is recommended. CUTTING MASONRY/METAL This tool is not recommended for continuous and general usage with metal or masonry cutoff wheels. If you use your saw for cutting these materials, use the appropriate wheel for the material being cut. When cutting masonry...