Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
4. Tighten the bevel adjustment knob (6) to secure the base plate. 8 Under bench use 1. Set the saw into the bench as required, ensuring the saw is secured adequately. 2. Attach a vacuum adapter to the saw. 3. Ensure the retracting blade guard can retract and return freely, operating as designed, before plugging cordset in the mains socket. 4. Run saw up to ensure it is running smoothly before attempting any cutting. 5. Make sure guarding is suitable so that the operator cannot touch the saw blade when the blade is spinning. 6. Make sure an anti-kickback device is fitted to your saw bench. 7. Make sure a suitable safety off switch is fitted to the saw bench. The saw switch may then be locked on using a spring clamp, cable tie or similar and then plugged into the safety socket on the saw bench. This clamp MUST be taken off when the saw is removed from the saw bench. 8. Using all safety equipment make a test cut in an off cut piece of material making sure all guarding is set up correctly before continuing with your bench sawing. Switching on and off 1. Connect the plug to the power supply. 2. To switch on the saw, press the lock-off button (2) and squeeze the trigger switch (1). 3. When you release the trigger, the machine turns off and re-engages the safety lock-off switch to help prevent accidental operation. Caution. Allow the blade to come to a complete standstill before setting the saw down. Making a cut 1. Adjust the depth and angle of cut as required. 2. Plug in the machine and start the motor. 3. Line up your pencil line with the correct sighting notch - for 90° cuts use the right hand (when viewed from the operators perspective) sighting notch (a) and for 45° cuts use the left hand sighting notch (b). 4. When the blade is at its maximum speed (approximately 2 seconds), slowly push the saw forward using both hands. Note. Use only enough pressure to keep the saw cutting. Do not force the saw so that there is an appreciable slowing of the motor. Allow the blade and the saw to do the work. a b 90. Cuts 45. Cuts 9 Using the parallel fence guide The parallel fence allows you to make parallel cuts in a sheet of wood, all at the same width. Caution. Always ensure that the saw is switched off and unplugged from the power supply before making any adjustments. 1. Slide the parallel fence (9) through the slots in the base plate. 2. Adjust the guide to the required width and secure it in position with the locking knob (8). 3. Ensure that the guide rests against the wood along its entire length to give a consistent parallel cut. Dust extraction You can connect the tool to a vacuum system via the dust extraction port (14). Changing the blade Caution. Always ensure that the saw is switched off and unplugged from the power supply before making any adjustments. 1. Rotate the saw blade by hand whilst depressing the spindle lock button (17) until the blade locks. 2. Turn the blade bolt anti-clockwise using the hex key (20) provided. 3. Remove the outer blade flange and the blade bolt. 4. Retract the lower blade guard (11) using the lever (10). 5. Remove the saw blade from the inner flange and pull it out. 6. Clean the saw blade flanges thoroughly before mounting the new saw blade. 7. Mount the new saw blade in reverse order and tighten the blade bolt. Warning. The direction in which the blade rotates has to be the same as the direction of the arrow marked on the housing. 8. Ensure that the spindle lock button (17) is released. 9. Before using the saw again, check that the safety devices are in good working order. Important. After replacing the saw blade, make sure that the saw blade runs freely by turning the blade by hand. WARNING: Plug the machine in to a power socket and run the saw under no load to check that it runs smoothly before using it to cut any material. 10 Maintenance 1. Keep the tool’s air vents unclogged and clean at all times. 2. Remove dust and dirt regularly. Cleaning is best done with a soft rag or a soft brush. Wear safety glasses to protect your eyes while cleaning. 3. Re-lubricate all moving parts at regular intervals. 4. If the body of the saw needs cleaning, wipe it with a soft damp cloth. A mild detergent can be used but nothing like alcohol, petrol or other cleaning agent. 5. Never use caustic agents to clean plastic parts. Caution. Water must never come into contact with the saw. General inspection Regularly check that all the fixing screws are tight. They may vibrate loose over time. Power cord maintenance If the supply cord needs replacing, the task must be carried out by the manufacturer, the manufacturer’s agent, or an authorised service centre in order to avoid a safety hazard. 11 Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Produc...