Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Fotos und technische Daten Royal Sovereign PL-1310 |
Anleitung Zusammenfassung
Hot and Cold Lamination The laminator can easily be adjusted to handle both hot and cold lamination pouch film. Thickness Control Individual settings for different film thicknesses from 3-10 mil. Ready Light A ready light clearly indicates when the machine has reached optimal temperature and is ready to laminate. Fast Speed Laminates up to 20” per minute. Automatic Shut-Off Function The machine will automatically shut off after one hour of idling. Reverse Functions The machine has both a manual and an automatic reverse function. 5 OPERATION Hot Lamination [Before laminating important or unique documents, always test a pouch through the laminator using a similar document.] 1. Place the machine on a flat, sturdy surface and press the power button to turn on the machine. 2. The machine is preset to the 3 mil setting. To change the setting, press the temperature control button. The machine will take approximately 4 minutes to warm-up. When the proper temperature is reached, the blinking light will glow steady. 3. Place the item to be laminated into the laminating pouch. 4. Insert the pouch film into the front opening of the laminator. Make sure to place the sealed end of the pouch film in first. All sized pouches should be placed in the center of the front opening to pass through the sensor. 5. The document or photo will then exit out the back of the machine. 6. If the item is not completely laminated, repeat step 4. NOTE: After inserting the pouch into the laminator, if the laminated item does not pass through all 4 rollers within approximately 15 seconds the automatic reverse function will turn on sending the item out of the front of the machine. If you need to reverse an item after it is inserted into the rollers press the reverse button and the item will exit the front opening NOTE: Laminated items exiting the machine may be too hot to touch. NOTE: Laminated items will be hot and will easily bend. To keep the item flat, place on a flat surface and allow it to cool. Cold Lamination 1. Place the machine on a flat, sturdy surface and press the power button to turn on the machine. 2. Press the temperature setting button until the Cold lamination setting is lit. If the machine was previously used in hot mode, allow approximately 40 minutes to cool down. When the proper temperature is reached, the light will glow steady. 3. Place the document to be laminated on the non-adhesive side of the cold film with the document face down, sealed end first. 4. Insert the document to be laminated into the front opening of the machine. 5. Remove paper liner from the cold film slowly while the document is being inserted into the machine. 6. The document or photo will exit out the back of the machine. NOTE: After inserting the pouch into the laminator, if the laminated item does not pass through all 4 rollers within approximately 15 seconds the automatic reverse function will turn on sending the item out of the front of the machine. If you need to reverse an item after it is inserted into the rollers press the reverse button and the item will exit the front opening. 6 PL-910/1310 TROUBLESHOOTINg Symptom Solution Motor does not work. Check to make sure machine is plugged in. Check to make sure the power button is turned on. Pouches are not laminating correctly. Make sure that the machine is set to the correct setting. The setting should be the same as the thickness of the pouch you are using. Ex.75 mic pouch film should be set to 3 mil setting. The machine is beeping and the pouch is returning out of the front of the machine. The automatic reverse function has turned on to retrieve the item. The item you are laminating may be jammed or too large to pass the rollers. Wait for the pouch to exit the front of the machine. You can try laminating again after 15 seconds. The rollers are moving, but the laminated item is not. Hold down the reverse button until the entire pouch has exited the front of the machine. You can try laminating again after 15 seconds. If you are still having complications, please contact Royal Sovereign’s Service Center at 1-800-397-1025. SPECIFICATIONS Model PL-910 PL-1310 Dimensions 17.6x7.3x4.6 in 448x186x118 mm 21.6x7.3x4.6 in 548x186x118 mm Maximum laminating width 9 " / 235 mm 13"/ 340 mm Maximum laminating thickness 27.6 mil / 0.7 mm Film thickness 3~10 mil / 75~250 micron Number of rollers 4 Cold mode Yes Heating system Hot shoe Ready time 4 min Motor type AC motor Laminating speed 20" per min. / 430 mm per min. Weight 8.4 lbs / 3.8 kg 15.4 lbs / 7 kg Voltage/Cycle 120V, 60Hz Power consumption 450 W 730 W 7 LIMITED ONE YEAR WARRANTY This warranty applies to repair or replacement of product found to be defective in material or workmanship for one year from the date of the original purchase. This warranty is extended only to the original purchaser. This warranty does not apply to damage resulting from abuse, misuse, or improper maintenance of damage that is attributable to acts of nature. Royal Sovereign In...
Dieses Handbuch ist für folgende Modelle:Laminiergeräte - PL-910 (724.99 kb)