Hersteller: Elation Professional Dateigröße: 2.9 mb Dateiname: dled_36_pro_manual_v1.4.pdf Unterrichtssprache:

Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite

- The DMX controller is switched off or defective. - The DMX cable or connector is defective. - A DMX terminator has been inserted into the last fixture in your DMX chain. DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 18 8. FIXTURE MENU On-Board System Menu: The Design LED 36 Pro™ comes with an easy to navigate system menu. This next section will detail the functions of each command in the system menu. LED Control Panel: The control panel located on the base of the fixture allows you to access the main menu and make all necessary adjustments to the Design LED 36 Pro™. During normal operation, tapping the “MENU” key once will access the fixture’s main menu. Once in the main menu you can navigate through the different functions and access the sub-menus with the Up and Down buttons. Once you reach a field that requires adjusting, tap the ENTER button to activate that field and use the UP and Down button to adjust the field. Tapping the Enter button once more will confirm your setting. Once a setting is saved the display will briefly readout OK to confirm a new setting has been made and locked into memory. You may exit the main menu at any time without making any adjustments by tapping the MENU button. MENU Button - To access the main menu locate the MENU button on the front of the unit. Press this button to activate the system menu. Tap the UP button until you reach the function you wish to change. When you reach the function you wish to change tap the ENTER button once to select that menu function. When a function is selected use the UP or DOWN button to change the function. Once your changes are made tap the ENTER button yet again to lock the change in the system menu. To exit without making any changes tap the MENU button. Default settings shaded. VALU A001~AXXX (AXXX) DMX address setting SLAV ON/OFF Set as Slave rdMX ON/OFF Change address via DMX AUtO ALON/MASt Run Auto program VALU D-XX D-00(DXXX) Display DMX value FLIP ON/OFF Flip display MOdE d ON ON/OFF Delay shutting off LED display SEt 3CH/4CH/6CH DMX channel Mode DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 19 Note: 1) If the fixture does not receive a DMX signal the menu display will flash repeatedly. 2) SPED: Adjust the hold time for each scene in built-in chase programs. 3) FADE: Adjust the fade time between each scene in the built-in programs. 8.1 “MOdE” - Function Mode: 8.1.1 - DMX address setting – This function is used to set or adjust the fixture’s starting DMX address. Every device controlled by DMX has to have a unique starting address. The addressing feature is what allows DMX to function properly. The DMX address of a fixture is what allows it to communicate with a controller properly. The DMX addressing also allows the fixture to ignore any DMX information coming from the controller that is not meant specifically for the fixture. Because each fixture is connected in a daisy-chain fashion it is imperative to assign a proper and unique starting DMX address to each and every fixture. The DMX address is non-destructive and will remain in the fixture’s memory even when the power to the unit is switched off. Memory is backed-up and retain by an internal power source that should last about five years. For proper DMX addressing see Section 9/Page 33 of this user manual. “VALU” - Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel. The display will automatically detail the changing DMX values as they are received from the MOd1 /Mod2 Dimmer Mode OFF/HOLd/AUtO Status while there is no DMX ON/OFF Default setting V-1.0~V-9.9 Software version MANL ~ 01 XX(00~FFH) 06 XX(00~FFH) Manual adjust intensity 0000~9999(hours) Total running hours CXXX Password used to clear run time ”038” tIME ON/OFF Clear fixture run time S-01~S-48 Select steps of program C-01~C-06 01 XX(00~FFH) 06 XX(00~FFH) FAdE XXX EdIt ~ tIME XXX.X(000.1s~999.9 s) Edit the internal scenes DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 20 controller. “SLAV” - Slave setting for Master/Slave Operation With this function, you can define the device as slave for operation in Master/Slave mode. Each slave setting will have a different function for a dynamic lightshow without a controller. “rdMX” - Address via DMX - This function allows the DMX address to remotely be adjusted from a DMX console. This setting requires special settings for both the controller and the fixture. RDMX is on by default. For operational instructions please see Section 9/Page 33 of this manual “Remote DMX addressing.” 8.1.2 - Internal Program Settings This function allows the internal programs to run in either stand-alone or master/salve mode. In “Master” mode the fixture will send DMX data to other fixtures connect via the DMX chain. In “...

Herunterladen

Geben Sie zwei Ziffern: