Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Royal Sovereign Dateigröße: 4.41 mb Dateiname: Unterrichtssprache:

(RSC-1650H and RSC-1650HR). Control Buttons 1. TEMPERATURE DISPLAY: Display’s current temperature (RSC-1650H and RSC-1650HR) 2. SPEED DISPLAY: Display’s current Speed. 3. TEMPERATURE BUTTON- (RSC-1650H and RSC-1650HR): To change the temperature (max. RSC-1650H: 122°F, 50°C/RSC-1650HR: 266°F, 130°C)ofthe upper roller, press up or down arrow button. 4. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers, press the up or down arrow button. 5. RUN: To start the rollers. 6. STOP: To stop the rollers. 7. REV: To reverse the rollers, press and hold the REVERSE button. 6 ¿RSË&rign 7. SPEED AND TEMPERATURE SETTINGS RSC-1650H/C/HR RSC-1 650H RSC-1 650H R Speed# Speed(Ft/min,M/min) Temp.# Temperature! °F,° C ) Temperature!” F,” C) 1 4(1.2) 1 No Heating No Heating 2 6(1.7) 2 No Heating 86(30) 3 7(2.2) 3 91 (33) 113(45) 4 9(2.6) 4 97(36) 140(60) 5 10(3.1) 5 104(40) 230(1 10) 6 12(3.6) 6 1 11 (44) 239(1 15) 7 14(4.2) 7 1 15(46) 248(120) 8 15(4.5) 8 1 17(47) 257(125) 9 16(5.0) 9 124(51) 266(130) 8. ROLLER NIP SETTING It is important to adjust the roller nip settings to the appropriate thickness of the board being used. Use the guide below to adjust to the correct position. NO. Inches Metric (mm) 1 Lamination Lamination 2 1/25" 1 3 3/16"~1/4" 5-7 4 3/ 8"~1/2" 10-13 5 3/5" 15 NOTE: If vou don't want to laminate.please place the pressure lever to the "Open positionfNQ.5Y'. 7 RSC Series 9. USING FOOT PEDAL AND REMOTE CONTROL USING FOOT PEDAL Place the foot pedal on the floor in front of the machine. Once all correct settings are displayed, you may use the foot pedal to operate the laminator for “Hands Free Operation.” To activate the machine, press the foot pedal once and then release. Repeat to stop the rollers. USING REMOTE CONTROL Located on the rear left side of the laminator. 1. PRESS RUN-To activate the rollers. 2. PRESS STOP - To stop the rollers from turning. 3. PRESS REV - To reverse the rollers. Press and hold the button (useful for jams or misted media). 1 2 3 8 ¿RS£ä*gn 10. USING CROSS CUTTER The cross cutter is located on the rear exit table of the machine. 1. After lamination, move the cutter approximately to the center of the completed application at the desired point of detachment (Figure 1). Figure 1 2. Grasp film with one hand, press the cutter downward into the application and slide it first to one end of the application, then to the other end to complete the cut (Figure 2 & 3). Figure 2 9 RSC Series 11. LOADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). Loading films to the top and bottom film shafts: (See page 5 for assistance with parts identification.) 1. Remove the top and bottom film shafts from the machine. 2. Load a roll of pressure sensitive film to the top film shaft (Figure 1). Center the film and tighten the core screws (Figure 2). 3. Load a roll of mounting film or roll of craft paper to the bottom film shaft. Do not tighten the core screws at this time.(Figure 3) Note: Please see the direction of the film on the top and bottom shafts. 4. Load the top and bottom film shafts onto the machine (Figure 4 & 5). 10 ¿RS§s£™9„ 12. THREADING FILM only RSC-1650HR 12.1. Decaling 1. Turn the power switch on (“I” position). The Power switch is located on the rear left side of the unit. 2. Complete the steps as in the “LOADING FILM” section (see page 10). 3. Set the top roller to the desired temperature (RSC-1650H and RSC-1650HR) 4. Take off the Frame-Paper Guide and the Feed Table. 5. Pull the top film down over the Safety Cover to the bottom of the craft paper / Mounting film. 6. Align and center the craft paper / Mounting film to the top film and tighten the two lower core screws (Figure 1). 7. Thread the top film underneath the Upper Idle Bar.(Figure 2) 8. Tape the top film on to the Release Liner Take-Up.(Figure 2) Figure 2 Figure 1 11 RSC Series 9. Cut and separate the release liner and the film. (Figure 3) 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4) 11. Reinstall the Feed Table and the Frame-Paper Guide,and close the Safety Cover. 12. Adjust the nip setting to appropriate gap. 13. Insert and push the leader board until they reach the front nip point. 14. Push the Run button. 15. Push the leader board into the rollers. (Figure 5) Figure 5 16. Adjust the top and bottom tension knob by rotating it clockwise or counterclockwise. Turn it until the top and bottom roll films have some resistance varies (the tension depending on the film thickness; the thicker the film the more tension is required). (F'gure 6) Figure 6 Figure 3 Figure 4 12 ¿RS§s£™9„ 17. Press the Stop button when the leader board has completely exited from the rollers. 18. Use the Cross Cutter to cut the leader board from the web (see page 9...

Herunterladen

Geben Sie zwei Ziffern: