Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Lea estas instrucciones antes del uso. fellowes.com Business Wire Binder Please read these instructions before use. Veuillez lire ces instructions avant utilisation. Lea estas instrucciones antes del uso. mm inch number of sheets 6mm 1/4” 2-35 8mm 5/16” 36-50 10mm 3/10” 51-61 11mm 7/16” 61-80 12mm 1/2” 81-100 14mm 9/16” 100-130 ENGLISH CAPABILITIES IMPORTANT SAFETY INSTRUCTIONS When punching; - always ensure the machine is on a stable surface - test punch scrap sheets and set the machine before punching final documents - remove staples and other metal articles prior to punching - never exceed the machines quoted performance WIRE COMB DIAMETER & DOCUMENT SIZES 2 Punching Capacity Paper sheets 70-80g / 20lb 15 sheet Transparent covers 100-200 micron / 4-8 mil 2 sheet 200+ micron / 8+ mil 1 sheet Other standard covers 160-270g / 40-60 lb 2 sheet 270+g / 60+ lb 1 sheet Waste tray capacity approx. 1500 sheet Binding Capacity Max wire comb size 14mm Max document (80g / 20lb) c. 130 sheet Technical Data Paper dimensions A4 Punching slots 34 Slot pitch 3: 1” Adjustable edge guide yes- rotary Net weight 7.8 kg / 17.2 lb Dimensions (LxDxH) 470 x 390 x 130mm / 18.5” x 15.3” x 5.1” Please keep for future reference. Read Before Using! Need Help? Customer Service…. Let our experts help you with a solution. Always call Fellowes before contacting your place of purchase. Storage and Document Measure Waste tray When binding; - take care, potential pinch point Waste tray Storage tray and Document measure Document support (lid) Punch handle Wire closing lever Wheel to adjust edge guide Adjustable edge guide Window Paper Entry Wire closing jaws Wire comb support 3 1. Ensure the machine is on a stable surface. 2. Check waste tray is empty and correctly fitted. 3. Lift the lid. Ensure the wire closing lever is pushed backwards. 4. Lift the punch handle to its upright position. BEFORE YOU BIND 1. Select the correct wire comb diameter using the comb storage tray. 2. Hang the selected wire comb onto wire comb support. STEPS TO BIND 1 1 2 3 4. Lift the wire comb upwards off the hooks. Carefully place into the open wire closing mechanism. Ensure the wire comb is open and touching the bottom of the mechanism. 5. Lift the wire closing lever forwards. The closing scale guide is on the moving jaw. Close the jaws until the wire gauge shows the size of wire being closed. 6. Check the closed seam. If the seam is not closed correctly, the document can be placed into the jaws and closed again. 7. To hide the seam, turn the rear cover backwards. The front cover is now visible. The seam is hidden inside the document. 6 7 3. Test punch scrap sheets to check edge guide setting. 3 SET UP 4 2 5 4 1. Punch sheets in small batches that do not overload the machine or user. 2. Starting with the rear cover. Load punched sheets directly onto the hanging open wire comb. 3. Punch and hang the front cover. Punch and hang the remaining sheets. 1 3 30 Max 15 (80gsm) 2 8. Check wire seam closure is complete. Loose binding allows sheet loss. Good closure retains all sheets. 8 CORRECTING A BOUND DOCUMENT REMOVAL OF WASTE CLIPPINGS Wire binding is a secure binding system. Additional sheets cannot be The waste tray is located under the machine and is accessed from the added unless the document is disassembled and then re-bound. right side. For best results empty the tray regularly. STORAGE Lower the punch handle to the horizontal position. Lower the lid. TROUBLESHOOTING Problem Cause Solution Punched holes are not central Edge guide not set Adjust edge guide until hole pattern is correct Machine will not punch Blockage Check waste tray in empty. Check for blockage to paper entry Punch holes are not parallel to edge Debris is stuck below dies Take stiff cardboard and slide into the paper entry. Move the cardboard sideways to release any stray clippings into the waste tray Partial holes Sheets not correctly aligned to punch pattern Adjust edge guide and test punch scrap sheets until correct Damaged hole edges Possibly overloading the machine Punch plastic covers with paper sheets. Reduce number of sheets being punched Waste tray leaks Waste tray is not correctly inserted or ‘burst Check waste tray is empty and ‘burst feature’ is closed feature’ has activated Sheets fall out of document Wire comb is not closed enough Check closure of wire comb. Place into closing mechanism and improve binding closure. WARRANTY Fellowes warrants all parts of the binder to be free of defects in material and workmanship for 2 years from the date of purchase by the original consumer. If any part is found to be defective during warranty period, your sale and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling or unauthorised repair. Any implied warranty, including that of merchantability or fitness for particular purpose, is hereby limited in duration to the appr...