Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Also, review the recommended tools list; carefully unpack and examine your new plumbing fixture. Channel Locks Drill Level Basin Wrench Tubing Cutter 10' Tape Measure Hacksaw INSTALLATION INSTRUCTIONS 15-3/4" (400mm) 8" (203mm) 31" (787mm) SUGGESTED 1-1/4" O.D. TAILPIECE 1-1/4" O.D. WASTE FINISHED FLOOR SUGGESTED SUPPLIES AS REQ'D 17" (432mm) 10-3/4" (273mm) 12-7/8" (327mm) 6-1/2" (165mm) TAILPIECE COUNTERTOP (BY OTHERS) * * * Cut a 2-1/2" (64mm) hole in the counter surface, allowing sufficient distance to the finished wall based on faucets choosen (Deck mount or Wall mount). PREPARE COUNTERTOP FOR INSTALLATION OF SINK FINISHED WALL 1-3/4" DIA. STD. DRAIN OUTLET 17" (432mm) 8-1/2" (216mm) 8-1/2" (216mm) OPTIONAL GRID DRAIN FINISHED WALL 1-3/4" DIA. STD. DRAIN OUTLET 17" (432mm) 8-1/2" (216mm) 8-1/2" (216mm) OPTIONAL GRID DRAIN Saber Saw Hole Saw INSTALL SINK COMPLETION OF INSTALLATION FINISHED FLOOR FINISHED WALL MASKING TAPE SINK GRID DRAIN BODY (1) COUNTER SURFACE (TYPICAL) Install faucet and fittings, trap, and connect to supply and drain stub in accordance with manufacturer's directions. Water test unit, check for leakage and correct as needed. FOAM SEAT WASHER (2) TAIL PIECE (6) LOCK NUT (5) GASKET RETAINING WASHER (4) GASKET SEAL (3) CUTOUT 2-1/2” The sink is mounted and secured on the countertop by the silicone. Install sink and drain as follows: 1. Place sink on counter surface, lining up the drain hole in the sink with drain hole cutout in the counter surface. Using masking tape, mark 3 points around base of sink to mark sink location. 2. Install drain supplied: a) Place foam seat washer (2), directly under the grid drain body (1). b) Drop grid drain body through drain hole of sink. c) From underneath the sink, slide gasket (3), retainer (4), and lock nut (5) onto the threaded grid drain body and tighten snugly into position. d) Install tail piece (6) into grid drain body (1). 3. With the location marked, pick up sink, turn it over, and apply a bead of adhesive-sealant to bottom of sink base. Place the sink down onto counter surface using marks as a guide. Remove excess adhesive-sealant around base of sink. Form a fillet of sealant with a wet finger or sponge. CARE AND MAINTENANCE CAUTION: Do not over-tighten. The nut on the drain should be finger tightened and then turned no more than one additional turn. In most cases, depending upon the drain chosen, plumbers putty or a series of rubber gaskets will be used to create a water tight seal. Over tightening also tends to press out or dislodge plumbers putty or distort rubber gaskets. The result could be a leaky drain and an overstressed point in the china. Do not use harsh abrasives or caustic cleaners to clean fixture surfaces. A mild detergent, warm water, and a soft cloth will remove normal dirt and soap accumulations from fittings and surfaces. Rinse thoroughly after cleaning and polish with a soft dry cloth to restore original luster of material. ! REPAIR PARTS LIST 738990-002A Overflow Cap 738989-0002A Chrome Grid Drain In the United States: American Standard Inc. P.O. Box 6820 Piscataway, New Jersey 08855 Attention: Director of Consumer Affairs For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 442-1902 In Canada: American Standard 2480 Stanfield Rd. Mississauga, Ontario Canada L4Y 1S2 Toll Free: (800) 387-0369 In Mexico: Customer Service Manager Ideal Standard, S.A. de C.V. Via Morelos #330 Col. Santa Clara Ecatepec 55540 Edo. Mexico AMERICAN STANDARD ONE-YEAR LIMITED WARRANTY If inspection of this American Standard plumbing product, within one year after its initial installation, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model. This limited warranty does not apply to local building code compliance; since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation. This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard. American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of imp...