Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Rotate the outfeed table handwheel until the outfeed table is nearly flush with the knife edge. 3. Position a steel straightedge on the outfeed table. Extend the straightedge over the middle of the cutterhead as shown in Figure 12. 2. Loosen the outfeed table lock knob located on the center of the outfeed table handwheel. Rotate the outfeed table handwheel until the outfeed table is nearly flush with the knife edge. 3. Position a steel straightedge on the outfeed table. Extend the straightedge over the middle of the cutterhead as shown in Figure 12. Outfeed Table Figure 12. Setting outfeed table with straightedge. 4. Raise or lower the outfeed table with the out- feed table handwheel until the straightedge barely touches the knife edge. Rock the cutterhead to ensure that the blade edge is at the highest point of its arc. Check the other two blades in the same manner. If they do not all touch the straightedge evenly, they are not at the same height. You must reset the knives. Be sure to test the height at both ends of the cutter knives. The knives must be parallel to the table surface. 5. Tighten the outfeed table lock knob. 6. Recheck the outfeed table alignment with each of the cutterhead knives and re-adjust as necessary. 7. Once properly set, the outfeed table height will only need to be changed when the knives are resharpened. -16- Ultimate Series Jointers Infeed Table To adjust the infeed table: 1. The infeed table can be adjusted the same way as the outfeed table. Loosen the infeed table lock knob in the center of the handwheel. 2. Place a straightedge on the outfeed table so it hangs over the infeed table. Turn the cutter- head so that the knives are NOT touching the straightedge. 3. Loosen the infeed table lock knob. Raise the infeed table until it just touches the straightedge as shown in Figure 13. Tighten the table lock knob. 4. Adjust the depth of cut scale to read “0”. Figure 13. Setting the depth of cut scale. 90° Fence Stop 1. Place a square on the outfeed table fairly close to the cutterhead as shown in Figure 14. Figure 14. Use of square to align fence. 2. While holding the fence adjusting handle, loosen the angle setting lock knob and the checknut on the 90° stop screw as shown in Figure 15. Turn the stop screw against the sliding bracket until the fence contacts the edge of the square evenly. 3. Tighten the checknut on the stop screw and tilt the fence back, then forward against the stop. 4. Recheck with the square. Tightening the checknut will move the stop bolt slightly, so some trial-and-error may be necessary to perfect your settings. 90° Stop Figure 15. Setting the 90° stop. Ultimate Series Jointers -17 45° Fence Stop 1. Place a 45° gauge on the outfeed table fairly close to the cutterhead as shown in Figure 16. 45° Stop Figure 17. Setting the 45° stop. Figure 16. Using a 45° gauge to align fence. 2. While holding the fence adjusting handle, loosen the angle setting lock knob and the checknut on the 45° stop screw as shown in Figure 17. Turn the stop screw against the sliding bracket until the fence contacts the edge of the 45° gauge evenly. 3. Tighten the checknut on the stop screw and tilt the fence forward, then back against the stop. 4. Recheck with the 45° gauge. Tightening the checknut will move the stop bolt slightly, so some trial-and-error may be necessary to perfect your settings. -18- Ultimate Series Jointers SECTION 6: OPERATIONS Test Run ! Disconnect power to the machine when performing any maintenance, assembly or adjustments. Failure to do this may result in serious personal injury. Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses during the entire operation process. Failure to comply may result in serious personal injury. Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your finger is poised on the STOP button, just in case there’s a problem. The jointer should run smoothly, with little or no vibration or rubbing noises. Strange or unnatural noises should be investigated and corrected before operating the machine further. If you cannot easily locate the source of an unusual noise or vibration, contact our service department for help. Stock Inspection If the stock has large or loose knots, consider finding another workpiece. Knots in a workpiece can be dangerous to the operator, as well as destructive to equipment. When jointing, always cut with the grain rather than against it. Cutting against the grain (going against the pattern of the wood’s growth rings) chips the wood instead of cutting it, making the workpiece rough and irregular. Look at the side of your board. If the direction of the grain structure facing the cutterhead runs toward the cutterhead as it sits on the infeed table, your cut will be with the grain as shown in Figure 18. Occasionally, you will fin...
Dieses Handbuch ist für folgende Modelle:Kantenfräse - G9860 (2.58 mb)
Kantenfräse - G9860ZX (2.58 mb)