Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
• If required, the plunge depth can be set accurately to within 0.1 mm. • Retighten button 9. Adjustment using the revolver- depth stop The revolver-depth stop enables you to quickly choose between six different cutting depths. These are also determined by the adjustment of the depth stop (10). • Adjust the required cutting depth by rotating the revolver-depth stop (21). Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005 Web Support: Model Number: PBF-1200 15 Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005 Web Support: Model Number: PBF-1200 06 Operation Height setting of the router column 151481112921 Fig. G Button (14) is used to set the maximum height of the router. The plunge depth is then fixed. This is usually necessary when using the tool on a special router table. Rough setting: • Loosen the clamping lever (11). The router can then be pushed down against the spring force. • Hold button (14) between your thumb and index finger. • Push the grey button (14) and use your other hand to push the router down at the same time. • Release the button. The router is now locked and will no longer return to its original position. Fine adjustment: • Turn button (14) clockwise. This causes the router column to slowly move down. • Turn button (14) counter-clockwise. This causes the router column to slowly move up. Setting the plunge depth Fig. G The plunge depth can be adjusted by using buttons 8, 9, 11 and 15. If the plunge Safety instructions (b) Do not operate this machine in potentially explosive environments containing combustible liquids, gases or dusts. Electric tools send out sparks which may ignite dust or vapours. (c) Keep children and other persons away from the electric tool during use. When distracted, you may lose control over the apparatus. 2) Electric safety (a) The plug of the machine has to be suitable for the socket. The connector may not be modified in any way. Do not use an adapter plug together with earthed devices. Unchanged connectors and fitting sockets reduce the risk of an electric shock. (b) Avoid body contact to earthed surfaces, such as pipes, radiator, stoves and refrigerators. There is a higher risk of an electric shock, if your body is earthed. (c) Keep the machine clear of rain or humidity. The penetration of water into an electrical device increases the risk of an electric shock. (d) Do not use the cable for unintended purposes, to carry or suspend the machine or to pull the connector out of the socket. Keep the cable clear of heat, oil, sharp edges or any moving parts. Damaged or entangled cables increase the risk of an electric shock. (e) When using an electric tool in the open, use an extension cable only which has been approved for outdoor use. The use of an extension cable suitable for use in the open will reduce the risk of an electric shock. Always use an RCD (redicual circuit device or circuit breaker). (f) Hold the machine at the insulated gripping surfaces as the belt grinder may hit its own power cord. Damaging a live cable may make metal machine parts live, which may lead to an electric shock. 3) Personal safety (a) Please pay attention and watch what you are doing, and carry out the work with the electric tool sensibly. Do not use the machine, when you are tired or under the influence of drugs, alcohol or medicine. A moment of carelessness in the use of the machine could lead to serious injuries. (b) Wear your safety equipment and always put on safety goggles. Wearing personal protective gear, such as dust mask, anti-skid safety shoes, hard hat and ear protection, depending on the type of use of the electric tool, will reduce the risk of injury. (c) Avoid unintentional operation. Make sure that the switch is in the “OFF” position before you remove the plug from the socket. If you have Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005 Web Support: Model Number: PBF-1200 07 Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005 Web Support: Model Number: PBF-1200 14 Safety instructions Operation your finger on the switch when carrying the machine or if you connect the running machine to the socket, this may lead to accidents. (d) Remove the adjusting tools or the spanners before switching on the machine. A tool or a key which is located in a revolving part of the machine may lead to injuries. (e) Concentrate at all times. Ensure a safe stand and keep your balance at all times. In this case you will be able to control the machine better in unexpected situations. (f) Wear suitable clothing. Do not wear any loose clothing or jewellery. Keep your hair, clothing and gloves clear of any moving parts. (g) If dust extraction or collection devices can be mounted, make sure that they are connected properly and are used in the proper way. The use of these pieces of equipmen...
Dieses Handbuch ist für folgende Modelle:Kantenfräse - Power Craft PBF-1200 (2.09 mb)