Anleitung Harbor Freight Tools, modell CENTRAL MACHINERY 95668
Hersteller: Harbor Freight Tools Dateigröße: 3.16 mb Dateiname: 95668.pdf
Unterrichtssprache:
|
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Anleitung Zusammenfassung
2. The V-Belt is slipping. 1. Make sure machine is plugged into a working, 110 volt, grounded, electrical outlet. 2. Adjust V-Belt tighter, or replace Belt. The Wood Shaper vibrates. The Spindle is loose. Or the Cutter “chatters”. 1. The Stand of the Wood Shaper is unstable and wobbles. 2. The Spindle or Cutter is loose or out of alignment. 3. The Wood Shaper has a loose Motor or Spindle Cartridge. 1. Stabilize the Stand on the floor. 2. Reinstall the Spindle and/or Cutter. 3. Have a qualified service technician check Motor and/or Spindle Cartridge. The Forward/Reverse Switch does not operate properly. 1. Defective Forward/ Reverse Switch. 1. Immediately turn off machine and unplug it from its electrical outlet. Do not operate machine until a qualified service technician repairs or replaces Forward/Reverse Switch. The Power Switch does not turn off Machine. 1. Defective Power Switch. 1. Immediately unplug machine from its electrical outlet. Do not operate machine until a qualified service technician repairs or replaces Power Switch. PARTS LIST Part # Description Part # Description 1 Side Panel 59 Fence Body (Left) 2 Tie Bar 60 Fence 3 Rubber Foot 61 Lock Handle 4 Philips Head Screw (M4-0.7x25) 62 Flat Washer (1/2”) 5 Power Switch 63 Flat Washer (3/8”) 6 Switch Lamella 64 Knob (M8-1.25) 7 Flat Washer (5mm) 65 Lock Washer (1/2”) 8 Hex Nut (M4-0.7) 66 Hex Bolt (M12-1.75 x 20) 9 Carriage Bolt (M8-1.25 x 12) 67 Adjusting Screw Stud 10 Flat Washer (3/8”) 68 Hand Knob 11 Hex Nut (M8-1.25) 69 Roll Pin (3 x 20) 12 Philips Head Screw (M5-0.8 x 12) 70 Philips Head Screw (M6-1 x 12) 13 Exterior Tooth Washer (5mm) 71 Half Collar 14 Hex Nut (M5-0.8) 72 Adjusting Shaft 15 Shelf 73 Flat Washer (1/2”) 16 Electricity Label 74 Hex Nut (M12-1.75) 75 Hex Bolt (M8-1.25 x 12) 18 Hex Nut (M8-1.25) 76 Flat Washer (3/8”) 19 Flat Washer (3/8”) 77 Hold Down Bar 20 Strain Relief 78 Philips Head Screw (M4-0.7 x 10) 21 Spindle Pulley Guard 79 Hex Post 22 Power Cord 80 Hex Nut (M8-1.25) 23 Wire Cord 81 Flat Washer (3/8”) 82 Mounting Bracket 83 Hand Knob 26 Flat Washer (3/8”) 84 Hex Nut (M4-0.7) 27 Hex Bolt (M8-1.25 x 12) 85 Ring Guard 28 Table Leg 86 Hex Bolt (M8-1.25 x 30) 87 Housing Bracket 30 Hex Bolt (M8-1.25 x 25) 88 Clamp Sleeve (Left) 31 Hex Bolt (M12-1.75 x 30) 89 Stuff Ring 32 Lock Washer (12mm) 90 Roll Pin (3 x 20mm) 33 Table Support 91 Lock Bar 34 Miter Block 92 Hand Knob 35 Flat Washer (1/4”) 93 Roll Pin (3 x 20mm) 36 Philips Head Screw (M4-0.7 x 6) 94 Lock Nut 37 Self Tapping Screw (3.5 x 12mm) 95 Hex Bolt (M12-1.75 x 30) 38 Flat Washer (3/8”) 96 Upper Spindle Nut 39 Support Pole 97 Safety Washer 40 Stud Bolt 98 Rub Collar (1/2” x 1-3/16” x 3/16”) 41 Anti-Kickback Pin 99 Rub Collar (1/2” x 1-3/16” x 1/4”) 42 Miter Bar 100 Rub Collar (1/2” x 1-3/16” x 3/8”) 43 Aluminum Alloy Fence 101 Cutter Spindle 44 Right Fence Lid 102 Collet Nut 44A Left Fence Lid 103 Collet 45 Miter Gauge Body 104 Collet 46 Plastic Handle 105 Spindle 47 Pointer 106 Key (4 x 4 x 20mm) 48 Self Tapping Screw (M3 x 15) 107 Interior Retaining Ring (47mm) 49 Tension Pin (2 x 16mm) 108 Wave Washer (45mm) 50 Carriage Bolt (M6-1 x 35) 109 Ball Bearing 51 Knob (M6-1.0) 110 Spindle Housing 52 Work Table 111 Ball Bearing Sleeve 53 Table Insert (1-3/8” Hole) 112 Ball Bearing 53A Table Insert (1-3/4” Hole) 113 Spindle Pulley 54 Carriage Bolt (M6-1 x 35) 114 Lower Spindle Nut 55 Knob (M6-1.0) 115 Bearing Cone 56 Taper Pin (8 x 75mm) 116 Coil Spring 57 Fence Body (Right) 117 Set Screw (M8-1.25 x 8) 58 Clamp Stud 118 Spring Collar NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. PARTS LIST (CONT.) Part # Description Part # Description 119 Stud 134 Hex Head Screw (M12-1.75 x 35) 120 Knob 135 Flat Washer (1/2”) 121 Draw Bar (M8-1.0) 136 Motor Mount Plate 122 Draw Bar Hex Nut (M8-1.0) 137 Flat Washer (3/8”) 123 Belt (690 x 10mm) 138 Hex Nut (M8-1.25) 124 Hex Bolt (M8-1.25 x 12) 139 Lock Washer (12mm) 125 Flat Washer (3/8”) 140 Lock Washer (8mm) 126 Belt Guard 141 Flat Washer (1/4”) 127 Motor Pulley 142 Shim 128 Set Screw (M6-1 x 10) 143 Philips Head Screw (M6-1 x 12) 129 Motor 144 Forward/Reverse Switch 129-1 Start Capacitor 145 Switch Bracket 129-2 Capacitor Cover 146 Arbor Wrench 129-3 Wiring Box 147 Tap Screw (M3.5 x 12) 129-4 Motor Fan 148 Right Fence Lid 129-5 Motor Fan Cover 149 Left Fence Lid 130 Key (5 x 5 x 22mm) 150 1/2” Spacer 131 Carriage Bolt (M8-1.25 x 40) 151 Long Hex Bolt M12 x 1.75 x 40 132 Lock Washer (8mm) 152 Short Hex Bolts M12 x 1.75 x 30 133 Flat Washer (3/8”) WIRING DIAGRAM Disconnect power from machine before performing any electri- cal service. Failure to do this will result in a shock hazard leading to injury. GREEN MOTOR BLACK WHITE GREEN POWER SWITCH BLACK WHITE CAPACITOR WHITE BLACK BLACK BLACK WHITE WHITE RED REAR VIEW OF SWITCH FWD/REV SWITCH REAR VIEW OF SWITCH REV 07j ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not...