Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
2920 CAUTION: READ ALL INSTRUCTIONS CAREFULLY wolfcraft BISCUIT JOINER • assembly • operating WARNING: FAILURE TO HEED ALL SAFETY AND OPERATING INSTRUCTIONS AND WARNINGS REGARDING USE OF THIS PRODUCT CAN RESULT IN SERIOUS BODILY INJURY. GENERAL SAFETY INSTRUCTIONS FORPOWERTOOLS 1. KNOW YOUR POWER TOOL Read the owner’s manual carefully. Learn its application and limitations as well as the specific potential hazards peculiar to this tool. 2. GROUND ALL TOOLS (UNLESS DOUBLE INSULATED) If tool is equipped with an approved 3-conductor cord and a 3-prong grounding type plug to fit the proper grounding type receptacle. The green conductor in the cord is the grounding wire. Never connect the green wire to a live terminal. 3. KEEP GUARDS IN PLACE In working order, and in proper adjustment and alignment. 4. REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 5. KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents. Floor must not be slippery due to wax or sawdust. 6. AVOID DANGEROUS ENVIRONMENT Don’t use power tools in damp or wet locations or expose them to rain. Keep work area well lighted. Provide adequate surrounding work space. 7. KEEP CHILDREN AWAY All visitors should be kept a safe distance from the work area. 8. MAKE WORKSHOP KID-PROOF —with padlocks, master switches, or by removing the starter keys. 9. DON’T FORCE TOOL It will do the job better and safer at the rate for which it was designed. 10. USE THE RIGHT TOOL Don’t force tool or attachment to do a job it was not designed for. 11. WEAR RIGHT APPAREL Do not wear loose clothing, gloves, neckties or jewelry (rings, wristwatches) to get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. Roll long sleeves above the elbow. 12. USE SAFETY GOGGLES (Head Protection) Wear Safety goggles (must comply with ANSI Z87.1) at all times. Also, use face or dust mask if cutting operation is dusty, and ear protectors (plugs or muffs) during extended periods of operation. 13. SECURE WORK Use clamps or a vise to hold work when practical. It’s safer than using your hand, frees both hands to operate tool. 14. DON’T OVERREACH Keep proper footing and balance at all times. 15. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 16. DISCONNECT TOOLS before servicing; when changing accessories such as blades, bits, cutters, etc. 17. AVOID ACCIDENTAL STARTING Make sure switch is in “OFF" position before plugging in. 18. USE RECOMMENDED ACCESSORIES Consult the owner’s manual for recommended accessories. Follow the instructions that accompany the accessories. The use of improper accessories may cause hazards. 19. NEVER STAND ON TOOL Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Do not store materials above or near the tool such that it is necessary to stand on the tool to reach them. 20. CHECK DAMAGED PARTS Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 21. DIRECTION OF FEED Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. 22. NEVER LEAVE TOOL RUNNING UNATTENDED Turn power off. Don’t leave tool until it comes to a complete stop. ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR WOLFCRAFT BISCUIT JOINER 1. ALWAYS USE EYE PROTECTION The operation of any power tool can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety goggles complying with ANSI Z87.1 before commencing power tool operation. 2. KEEP TOOL CLEAN After every use, clean sawdust off the Biscuit Joiner and angle grinder. 3. WARNING: Always turn “OFF” the angle grinder and disconnect the power cord when installing the cutter and/or adjusting the depth of cut. INTRODUCTION The Wolfcraft Biscuit Joiner is designed for creating joints in pressed woods and other soft woods that do not accept dowels, dovetails or other types of joints. It can be used for a variety of purposes, including corners, mitres and “T” joints. With a special attachment (included), it can also be used to create grooves in plywood or other material. The Wolfcraft Biscuit Joiner attaches to most popular angle grinders. It can be used to cut #0, #10 and #20 slots at 45° 90° and 180° angles. UNPACKING AND CHECKING CONTENTS Before beginning work, separate all the parts from the packaging materials and check each one against the parts list on page 8 to be sure...