These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires. 9 Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions Installing a J-Model in an existing wall case. Read these instructions completely and carefully. IMPORTANT! GE strongly recommends the removal of the old wa

To replace: Hook the tabs on the front grille even with the tabs on the case and snap into place. Replace the screws and filter. Front Grille Care and cleaning of the air conditioner. Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support Outdoor Coils The coils on the outdoor side of the air conditioner should be checked regularly. If they are clogged with dirt or soot they may be professionally steam cleaned, a service avail

2. Carefully remove 6. of the cordset insulation so as to expose the three insulated wires. 3. Strip 3/4. of the insulation away at the end of each of the three wires (L1, L2 and Ground). 4. Direct connection to branch circuit wiring inside the provided junction box must be made by connecting as follows in steps 1–3 below. 3/4. 6. Connector 7. FOR 265 VOLT DIRECT CONNECT APPLICATIONS ONLY IMPORTANT: Connection of a 265V AC product to a branch circuit MUST be done by direct connection in accordan

Replacing an existing unit? For details, see the Installation Instructions in this manual. READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS 2 About the controls on your Zoneline. ge.com TEMP CONTROL MODE CONTROL Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Consumer Support Controls Temp Control The temp control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same comfort level. When y

Branch Circuit and Proper GE Unit Amperage Rating Subbase Kit 15 RAK204D15P 20 RAK204D20P 30 RAK204D30P* 14 Installation Instructions 265 VOLT ELECTRICAL SUPPLY JUNCTION BOX Remove the junction box cover by taking out the Remove the junction box by taking out the top rear . Note how the tab on the lower right corner ves to hold the side in place. This will help when the box is being reinstalled. The cord will be coiled up inside the junction box. 1 Unit connector Junction box cover Junction box

You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded. READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS 4 About the controls on the air conditioner. OFF LOW FAN HIGH FAN HIGH HEAT HIGH COOL LOW COOL LOW HEAT WARMER COOLER OFF LOW FAN HIGH FAN HIGH COOL LOW COOL COOLER MODE CONTROL TEMP CONTROL Controls Mode Control HIGH COOL and LOW COOL provide cooling with different fan speeds. HIGH HEAT and LOW HEAT provide heatin

2 Connect to electrical power. 3 See the special instructions below for applicable supply voltages. 4 Reinstall the room cabinet. Branch Circuit and Proper GE Unit Amperage Rating Subbase Kit 15/20 RAK204D20 30 RAK204D30 230/208 VOLT ELECTRICAL SUPPLY All wiring, including installation of the receptacle, must be in accordance with the NEC and local codes, ordinances and regulations. This unit is equipped with a line cord for appropriate amperage wall receptacle. See below. Electrical subbases pr

Secure the case through the case track into the window stool on each side, using two 1. screws. Secure to stool 6 Assemble and Attach the Sill and Support Brackets Attach both sill brackets to the window sill using a 1. long screw on each side. Tighten the bolts and nuts on both sides. Loosely attach the sill brackets to the support brackets with 5/8. long carriage bolts and nuts. Find the track hole that aligns with the sill bracket on the outer edge of the window sill. Using the 5/8. long mach

• Includes 3-meter conductor wire for hook-up to Vertical Zoneline. • Required for Motion Sensor/Door Switch applications. * A-B Series: Zonelines® built before 1987 – Zoneline I, II, III, and IV; AZC Series: Zonelines built from 1987 to 1992 – includes AZR Series – Zoneline 1000, 2000, 2500, 2700, 3000, 4000, 5000; AZ Series: Zonelines built after 1992 – Zoneline 2100, 3100, 2600, 5100 / Zoneline 2200, 3200, 5200 / Zoneline 2500, 3500, 5500 / Zoneline 2800, 3800, 5800. RAVWP6 (AZ Series*—7500)

21 Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support Through-the-wall installation. Read these instructions completely and carefully. Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions 1 Preparation of the Opening in the Wall Make certain a wall receptacle is available close to the hole location or make arrangements to install a receptacle. The cord