Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
MODEL NUMBER DESCRIPTION TABLE 2 CAF-6 B 2 05 11 01 A1 or Refer to CCAS-8 Code Control Options (Factory Installed) Wiring Diagram 00 = No Optional Control A A1 = Built-in SP tamperproof thermostat 120 - 277V C A2 = Built-in DP tamperproof thermostat 120 - 277V E F1 = Built-in SP adjustable thermostat 120 - 277V C F2 = Built-in DP adjustable thermostat 120 - 277V E A4 = Built-in 24V low voltage relay 120 - 277V D A5 = Built-in 24V low voltage relay and transformer 120 - 277V F A8 = Built-in disconnect switch, rated 277V@20A B B1 = Built-in SP tamperproof thermostat and disconnect G B2 = Built-in DP tamperproof thermostat and disconnect H F3 = Built-in SP adjustable thermostat and disconnect G F4 = Built-in DP adjustable thermostat and disconnect H D1 = Built-in low voltage relay and disconnect D2 = Built-in low voltage transformer and disconnect Painted Anodized 68 = Almond 07 = Bronze 02 = White 10 = Clear Code Voltage/Phase 11 = 120/1 21 = 208/1 31 = 240/1 41 = 277/1 Code Wattage (See Table) Code Length 2 = 2 ft. 3 = 3 ft. 4 = 4 ft. 5 = 5 ft. 6 = 6 ft. 7 = 7 ft. 8 = 8 ft. 9 = 9 ft. 10 = 10 ft. Code Inlet Location F = Front B = Bottom Type GENERAL This document explains the correct procedure for the installation and safe operation of all models of Draft Barrier and Pedestal Mounted Heaters. Draft Barrier Heating Systems are designed to be installed in accordance with the National Electrical Code and with local codes by a qualified person. General Information — Draft Barriers and Pedestal Mounted Heaters are intended for wall, sill or floor mounting. The heaters are designed so that they may be used as an individual cabinet convector, in a wall-to-wall configuration or as an end-to-end continuous perimeter room heating system. Draft Barrier heating systems are supported by a wide selection of controls and accessories designed to solve any heating requirement. Before You Unpack — 1. Make certain that the number of cartons received agrees with the Bill of Lading, Packing List and original order. Also check that the correct style (Model) and color have been shipped. 2. Every heater is carefully inspected and shipped with a clear Bill of Lading. Obvious external and/or concealed damage must be reported to the carrier for remedy. WARNING: Hazard of Fire 1. DO NOT INSTALL HEATERS AGAINST ANY HIGHLY COMBUSTIBLE SURFACES SUCH AS LOW DENSITY CELLULOSE FIBRE. 2. DO NOT LOCATE HEATER BELOW ELECTRICAL CONVENIENCE RECEPTACLES. 3. DO NOT STORE OR USE GASOLINE OR FLAMMABLE LIQUIDS IN THE VICINITY OF THE HEATERS. WARNING: Hazard of Fire. The normal operating temperatures of cabinet convectors are relatively high and proper operation requires free circulation of room air through the heating element. Bottom air inlet heaters must be mounted with minimum of 2” from finished floor. WARNING: Hazard of Fire. Keep electrical cords, drapes, rugs and other furnishings away from the heater. WARNING: Hazard of Fire. Furniture must be placed no closer than four inches from the heater (see Figure 1) WARNING: Hazard of Fire. Drapes must clear the top of heater by at least twelve inches; or, if floor length drapes are used, they must clear the finished floor by three inches and the minimum clearance from the back fold to the front cover should be at least four inches (see Figure 1) WARNING: Hazard of Fire. When the floor is to be finished in carpet, allow clearance under the heaters and corners for carpet installation. Bottom air inlet heaters are to be mounted a minimum of 2” from the finished floor. WARNING: Hazard of Fire. Rugs may be placed up to a heater provided that they are not of a thickness that would block the air-intake. Bottom air inlet heaters are to be mounted a minimum of 2” from the finished floor. Figure 1: Furniture & Drapes GENERAL Draft Barrier Heater Installation (Wall) 1. Once the correct mounting height is established, scribe or snap a level line on the wall to maintain each heater back plate in horizontal alignment, when mounting. 2. Remove heater front cover by lifting top rear edge to unsnap cover from back plate (store cover in safe location to avoid damage to the finish). (See Figure 2). 3. Remove all appropriate knockouts from terminal boxes, particularly terminal box end knockouts when installing continuous run heating. (See Figure 3). 4. Mount the back panel to the wall using suitable fasteners (not supplied). Should the wall surface be uneven, secure the heater backplate to the high spots only to avoid a distorted appearance. Draft Barrier Heater Installation (Floor) 1. Unpack the heater and pedestal(s) from the carton (The pedestals are packed at the end of carton) and lift the front/top panels up and off the heater. 2. Disassemble the pedestal base from the pedestal pad. 3. Remove the desired terminal box cover(s) and supply wire entry knockouts from the terminal boxes. 4. Secure a pedestal to each end of the heater bottom with #8 screws provided aligning the back and front edges of the pad with the heat...
Dieses Handbuch ist für folgende Modelle:Splitgeräte - CCAS-8 (218.55 kb)