Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Do not use plug adapters or an extension cord with this appliance. If the power cord is too short, have a qualified electrician or service technician install an outlet near the appliance. 9 OPERATING YOUR AIR CONDITIONER Control Panel Key Pad TEMPERATURE Press up and down keys to select a suitable temperature setting. The temperature selected will be displayed in the LCD window. Temperature settings are adjustable between 15.C (58.F) to 31.C (90.F). SPEED Press speed key and the speed sequence will be displayed in the LCD window. (LOW – MED - HIGH) MODE Each pressing of the mode key will advance to a different mode setting. (AUTO – COOL – FAN – HUMIDIFY – HEATING) The running mode selected will be displayed in the LCD window. TIMER ON/OFF Press this key to set desired auto -timer settings sequences of 30 minutes, from . hour to 12 hours. Every time you press the “TIMER” key, the “AUTO OFF” time will be displayed in the LCD window. The same applies to “AUTO ON” time. ON/OFF To turn power on, press ON/OFF key once. The unit will run at auto mode. LCD window will display “AUTO”. 10 AUTO Display When this sequence is selected after pressing the MODE button, the corresponding signal indiactor is lit. In this mode, your unit will logically choose a desired room temperature. If the temperature is not comfortable for you, the desired MODE can be select manually. FAN Display When this sequence is selected the corresponding signal indicator is lit, after pressing the mode button. TEMPERATURE Display When these buttons are pressed, the corresponding area will show the selected temperature. COOL Display When this sequence is selected, after pressing the MODE button, the signal indicator is lit. Then push the temperature buttons to set the desired room temp. HUMIDIFIER Display When this sequence is selected after pressing the mode button, the corresponding signal indicator is lit. Under this mode, you cannot select a fan speed or adjust the temperature since the fan motor operates at a pre-set fan speed. 11 REMOTE CONTROL OPERATION The remote control uses 2 alkaline dry batteries (AAA 1.5V). To install the batteries, slide back the cover and mount them according to the (+ and -) signs shown on the rear compartment. NOTE: If you plan not to use the control for several weeks, remove the batteries. When replacing the batteries, do not mix old and new. Replace the batteries when the transmission indicator light fails to appear. ON/OFF Button: Press ON/OFF button when the portable air conditioner is ready for use. The unit is ready to be programmed in auto mode. The LCD window will display “AUTO”. MODE Button: Push the “MODE” button. Each time you press the button, a mode is selected in a sequence that goes form AUTO – COOL – FAN – HUMIDIFIER - HEATING 12 CARE AND MAINTENANCE ? When servicing the air conditioner, be sure to turn the operation switch to the “OFF” position and disconnect the power cord from the electrical outlet. ? Do not use gasoline, benzine, thinner or other chemicals on the air conditioner as these substances may cause damage to the paint finish and deformation of plastic parts. ? Never attempt to pour water directly to the front of the unit as this will cause deteriora tion of the electrical insulation. Cleaning the Air Filter If the air filter becomes clogged with dust, airflow is obstructed and reduces efficiency. The air filter should be cleaned once a month. More frequent cleaning may be necessary depending on outdoor and indoor air quality. The air filter is located behind the air intake front grille. To remove the air filter, grasp the filter handle (tab) located on the right (center) side of the air inlet grille and slide the air filter out. See Fig. 17. To reinstall the air filter, reverse the above procedure. Remove dust clogged in the filter by tapping it or vacuum clean it. Wash the filter well with lukewarm water below 40.C (104.F) while rubbing lightly: To get better results, wash it with soapy water or a neutral cleaning agent. Rinse the filter well using clean water, then dry completely. End-of-Season Care ? Operate the fan alone for half a day to dry out the inside of the unit. ? Turn off power and remove plug from wall socket. ? Clean filter. ? Store in dry location. Fig. 17 13 PROBLEMS WITH YOUR AIR CONDITIONER? You can solve many common air conditioner problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling theservice. TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE SUGGESTED SOLUTION Air conditioner does not operate. No power to the unit. Check connection of power cord to power source. The circuit breaker tripped or a blown fuse. Set OPERATION knob to position other than “OFF”. Inefficient or no cooling. Dirty air filter. Inappropriate capacity for application. Blocked airflow. Power interruption, settings change too quickly, or compressor overload tripped. Clean or replace air filter. Check with dealer ...