Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Goodman Mfg Dateigröße: 285.38 kb Dateiname: IO-230F.pdf Unterrichtssprache:

INDEX INTRODUCTION .................................................................... 2 REPLACEMENT PARTS ........................................................ 2 SAFETY INSTRUCTIONS ...................................................... 2 WARNINGS ............................................................................ 2 MODEL IDENTIFICATION ...................................................... 3 PRODUCT DESCRIPTION ..................................................... 3 UNIT INSPECTION ................................................................. 4 ELECTRIC HEAT .................................................................... 4 HKR INSTALLATION .............................................................. 5 LOCATION .............................................................................. 5 DUCTWORK ........................................................................... 5 ELECTRICAL SUPPLY WIRE AND MOP ............................... 5 REFRIGERANT LINES ........................................................... 6 AEPT MOTOR ORIENTATION ............................................... 8 CONVERSION TO DOWNFLOW ........................................... 8 CONVERSION TO HORIZONTAL .......................................... 9 CONDENSATE REMOVAL ..................................................... 9 ACHIEVING 2% LOW LEAKAGE RATE .............................. 10 ARUF/ARPF MOTOR ........................................................... 10 AEPT MOTOR.......................................................................10 THERMOSTAT WIRING DIAGRAMS ................................... 11 THERMOSTATS.................................................................... 13 INTRODUCTION Checking Product Received Upon receiving the product, inspect it for damage from shipment. Claims for damage, either shipping or concealed, should be filed immediately with the shipping company. Check the product to determine if it is correct. In the event an incorrect product is shipped, it must be returned to the supplier and must NOT be installed. The manufacturer assumes no responsibility for installation of incorrectly shipped products. Before Beginning Installation Carefully read all instructions for the installation prior to installing product. Make sure each step or procedure is understood and any special considerations are taken into account before starting installation. Assemble all tools, hardware and supplies needed to complete the installation. Some items may need to be purchased locally. Make sure everything needed to install the product is on hand before starting. REPLACEMENT PARTS Ordering Parts When reporting shortages or damages, or ordering repair parts, give the complete product model and serial numbers as stamped on the product. Replacement parts for this product are available through your contractor or local distributor. For the location of your nearest distributor consult the white business pages, the yellow page section of the local telephone book, or contact the following: SERVICE PARTS DEPARTMENT GOODMAN MANUFACTURING COMPANY, L.P. 2550 NORTH LOOP WEST, SUITE 400 HOUSTON, TEXAS 77092 (713) 861 – 2500 IMPORTANT SAFETY INSTRUCTIONS Recognize Safety Symbols, Words, and Labels The following symbols and labels are used throughout this manual to indicate immediate or potential hazards. It is the owner’s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed safety information increases the risk of serious personal injury or death, property damage and/or product damage. DANGER IMMEDIATE HAZARDS WHICH WILL RESULT IN PROPERTY DAMAGE, PRODUCT DAMAGE, SEVERE PERSONAL INJURY OR DEATH. WARNING HAZARDS OR UNSAFE PRACTICES COULD RESULT IN PROPERTY DAMAGE, PRODUCT DAMAGE, SEVERE PERSONAL INJURY OR DEATH. CAUTION HAZARDS OR UNSAFE PRACTICES WHICH MAY RESULT IN PROPERTY DAMAGE, PRODUCT DAMAGE, PERSONAL INJURY OR DEATH. WARNING THE UNIT MUST HAVE AN UNINTERRUPTED, UNBROKEN ELECTRICAL GROUND TO MINIMIZE THE POSSIBILITY OF PERSONAL INJURY IF AN ELECTRICAL FAULT SHOULD OCCUR. THE ELECTRICAL GROUND CIRCUIT MAY CONSIST OF AN APPROPRIATELY SIZED ELECTRICAL WIRE CONNECTING THE GROUND LUG IN THE UNIT CONTROL BOX TO THE BUILDING ELECTRICAL SERVICE PANEL. OTHER METHODS OF GROUNDING ARE PERMITTED IF PERFORMED IN ACCORDANCE WITH THE “NATIONAL ELECTRIC CODE” (NEC)/”AMERICAN NATIONAL STANDARDS INSTITUTE” (ANSI)/”NATIONAL FIRE PROTECTION ASSOCIATION” (NFPA) 70 AND LOCAL/STATE CODES. IN CANADA, ELECTRICAL GROUNDING IS TO BE IN ACCORDANCE WITH THE CANADIAN ELECTRIC CODE CSA C22.1. FAILURE TO OBSERVE THIS WARNING CAN RESULT IN ELECTRICAL SHOCK THAT CAN CAUSE PERSONAL INJURY. WARNING BEFORE SERVICING OR INSTALLING THIS EQUIPMENT, THE ELECTRICAL POWER TO THIS UNIT MUST BE IN THE “OFF” POSITION. CAUTION, MORE THAN ONE DISCONNECT MAY EXIST. FAILURE TO OBSERVE THIS WARNING MAY RESULT IN AN ELECTRICAL SHOCK THAT CAN CAUSE PERSONAL INJURY. WARNING DUE TO HI...

Herunterladen

Geben Sie zwei Ziffern: