Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
ENGLISH Owner's Manual 11 Electrical Safety Temporary Use of an Adapter We strongly discourage the use of an adapter due to potential safety hazards. For temporary connections, use only a UL-listed adapter, available from most local hardware stores. Ensure that the large slot in the adapter is aligned with the large slot in the receptacle for a proper polarity connection. To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal damage. Temporary method Adapter Plug Receptacle Cover Metal Screw WARNING: Never use the appliance with a broken adapter. Temporary Use of an Extension Cord We strongly discourage the use of an extension cord due to potential safety hazards. For temporary situations, use only CSA certified and UL listed 3-wire grounded extension cords, rated 15 A, 125 V. 12 Room Air Conditioner Owner's Manual 13 Operating Instructions ENGLISH Operating Instructions How to insert the Batteries Storage and Tips for using the Remote Controller 1. Remove the battery cover by pulling it according to the arrow direction. 2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly. 3. Reattach the cover by sliding it back into position. Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries. NOTICE • The remote controller may be stored by mounting it on a wall. • To operate the room air conditioner, aim the remote controller at the signal receptor. Signal receptor Receives the signals from the remote controller.(Signal receiving sound: two short beeps or one long beep.) Operation indicating lamps On/Off : Lights up during the system operation. Sleep Mode : Lights up during Sleep Mode Auto operation. Timer : Lights up during Timer operation. Defrost Mode : Lights up during Defrost Mode or *Hot Start operation (Heat pump model only) : Lights up during outdoor unit operation. (Cooling model only) NEO Plasma : The function illustrates its dynamic mode by using a multiple lighting system. Outdoor Unit Operation Operation indicating lamps *Hot Start operation: Stops the indoor fan in Heating Operation to prevent cold air from blowing out from unit. Operating Instructions Remote Control Operations The controls will look like the following. Controls Signal transmitter ON OFF CANCEL SET 1 3 5 4 9 10 12 14 16 7 2 8 13 15 11 6 Cooling Operation Auto Operation or Auto Changeover Healthy Dehumidification Operation Flip-up door (opened) Heating Operation • Cooling Model( ), Heat Pump Model( ) 17 AUTO CLEAN Operation Mode 1. START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2. OPERATION MODE SELECTION BUTTON Used to select the operation mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4. INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps low, medium, high and CHAOS. 5. JET COOL/HEATING(OPTIONAL) Used to start or stop the speed cooling/heaing.(speed cooling/heating operates super high fan speed in cooling/heatig mode.) 6. CHAOS SWING BUTTON Used to stop or start louver movement and set the desired up/down airflow direction. 7. ON/OFF TIMER BUTTONS Used to set the time of starting and stopping operation. (See page 24) 8. TIME SETTING BUTTONS Used to adjust the time. (See page 24) 9. TIMER SET/CANCEL BUTTON Used to set the timer when the desired time is obtained and to cancel the Timer operation. (See page 24) 10. SLEEP MODE AUTO BUTTON Used to set Sleep Mode Auto operation. (See page 24) 11. AIR CIRCULATION BUTTON Used to circulate the room air without cooling or heating. (See page 25) 12. ROOM TEMPERATURE CHECKING BUTTON Used to check the room temperature. 13. NEO PLASMA(OPTIONAL) Used to start or stop the plasma-purification function. (See page 22) 14. HORIZONTAL AIRFLOW DIRECTION CONTROL BUTTON (OPTIONAL) Used to set the desired vertical airflow direction. 15. RESET BUTTON Used prior to resetting time. 16. 2nd F Button Used prior to using modes printed in blue at the bottom of buttons. (See page 23) 17. AUTO CLEAN (OPTIONAL) Used to set Auto Clean mode. 14 Room Air Conditioner Operating Instructions Cooling operation ON Cooling Healthy Dehumidification Auto Heating (Heat pump model only) To lower the temperature To raise the temperature Press the Start/Stop button. The unit will respond with a beep. Open the door of the remote controller. To select Cooling Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Close the door of the remote controller. Set the temperature lower than the room temperature. The temperature can be set within a range of 18°C~30°C at intervals of 1°C. Set the fan speed again with the door of the remote controller still closed. You can select the fan speed in four steps-low, medium, high and CHAOS. Each time the button is pressed...
Dieses Handbuch ist für folgende Modelle:Splitgeräte - A18AHM NV2 (2.26 mb)