Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
• It must be protected with a 10 A slow- action fuse. • Should an extension lead be required, then this lead should be at least 1.5 mm2 thick per terminal, less than 25 m long and earthed. • There is a cavity at the back of the appliance to house the mains electricity supply cable. See Fig. 2. • Do not allow water to enter your appliance and do not cover the air intakes/outlets. • For safety reasons, the appliance must be at least 20 cm away from any nearby surface before it is turned on, Fig. 5. min. 20 cm. Fig. 5 min. 20 cm. Warning! The mains electricity supply connection cable must only be replaced by authorised members of the manufacturer’s Official Technical Service. When the appliance is turned off and then turned back on, it takes the compressor 3 minutes to start up again. This period of time is required in order to ensure correct operation. Avoid direct contact with the air expelled through the expulsion tube. Navigation The control panel is designed to make it easier to use your appliance. The following points need to be taken into consideration. The "up" and "down" keys are used to move up and down the screen. The "+" and "–" keys (right and left) are used to move to the right and to the left in the selection box. The box shows the function selected for modification. The following is an example of navigation: Up and down keys The "up" and "down" keys are used to move up and down the screen. "Down" key : Starting from the screen shown in the first figure (the selection box is situated on the operation function option). If you press key , the selection box moves down to the "Temperature selection" function. 56 Navigation If you press key again, the selection box moves down to the "speed selection" function. "Up" key : Key works in exactly the same way as key , the selection box moving up rather than down. Cyclical operation: Both keys work cyclically, i.e. if the selection box is at the bottom of the screen and key is pressed again, the selection box moves to the top of the screen. Likewise, if the selection box is at the top of the screen and key is pressed, the selection box moves to the bottom of the screen. "+" and "–" keys The "+" and "–" keys are used to move to the right and to the left within the selection box. If the function selected is temperature, these keys are used to increase and reduce the desired temperature as shown below: 57 Instructions for Use 58 Preparing the appliance before use Installing the air expulsion tuben • Fit the air expulsion tube assembly into the housing on the top of the appliance at the back, Fig. 7. In order to fit the expulsion tube assembly properly in its housing, it is necessary to slide the sleeve into the positioning slot (as shown by the arrows on Fig. 8). The diffusion duct, Fig. 6, is added when the tube assembly has been fitted onto the appliance. Press the "Push" ab (Fig. 9, 1.) and slide out (Fig. 9, 2.) to remove the assembly from the appliance. Installation for the dehumidification and air purification function • Remove the diffusion duct and set the air expulsion tube to the position shown in figure 10. • The expulsion tube may also be totally dismantled if desired. Fig. 6 Fig. 7 Hueco para la ubicacion del conjunto tubo expulsor de aire Fig. 10 Fig. 8 Fig. 9 Installing the air expulsion accessories for the air-conditioning function There are a set of accessories used to expel hot air (see "Description of accessories"). Installing the suction pad • Open the window slightly and position the diffusion duct between the jamb and the glaze frame. • Close the window as far as possible and secure it with the suction pad supplied, Fig. 11. Fig. 11 Installing the sliding window / balcony accessory • The sliding window/balcony installation accessory supplied with your appliance can also be used (See "Description of accessories"), Fig. 12 : a, b, c, d. This accessory can be used for both horizontal and vertical windows. Instructions for Use 59 a b Permanent installation Performed using the wall grommet / window grommet accessory. See "Description of accessories". • To expel hot air through the wall, it is necessary to make a hole in the wall and fit the wall grommet, Fig. 14. Fig. 12 c d • The accessory has two holes on the side to fit it to the window / balcony with. The user can secure it to the frame or wall with two screws (not included with the accessory) to prevent it from moving or falling out of place, Fig. 13. Fig. 13 24 - 38 cm. • Remove the diffusion sleeve and connect the air expulsion tube to the accessory. • If permanent installation is to be performed through the window, then it is only necessary to use the transparent end piece on the accessory. A 10.5-cm diameter hole needs to be cut in the glass, Fig. 15. Fig. 14 Fig. 15 Notes: Do not extend the hot air expulsion tube more than necessary (maximum length; 140 cm). Do not form sharp bends when positioning the tube, otherwise the Do not form sharp bends when positioning the tube, otherwise ...
Dieses Handbuch ist für folgende Modelle:Splitgeräte - 3XM202H/02 (2.57 mb)